Ecco EC2030-WC2 Instrucciones De Funcionamiento

WARNING!
Failure to install or use this product according to manufacturer's recommendations may result in property damage, serious injury, and/or death to
those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understood the safety
information contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure the
safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing, which can
cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of the system is
maximized and the controls are placed within convenient reach of the operator so that they can operate the system without losing eye contact with
the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment area
may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death. Refer to the vehicle owner's
manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable mounting location ensuring the safety of
all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator should
ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people, vehicles or other
obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal. Never take the
right-of-way for granted. It is the vehicle operator's responsibility to be sure they can proceed safely before entering an intersection, drive against
traffic, respond at a high rate of speed, or walk on or around traffic lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding
emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer assumes
no liability for any loss resulting from the use of this warning device.
Specifications:
Battery Capacity
Charging Voltage
Charging Time
Discharging Time
Charging Temperature
Waterproof Rating
Image Device
Effective Pixels
Sensing Area
Operation Frequency
Line of Sight Range
Delay
Night Vision Distance
Audio
Viewing Angle
IR-Cut
Standby Mode
Magnetic Strength
Operating Instructions:
Power Button:
Long press for 3 seconds to enter work or sleep mode,double-click to enter
standby mode and click to enter work mode.
Automatic Standby and Wake Up: When monitor enters standby mode for 30s,
camera will enter standby mode, when monitor goes back to work, camera
will be woken up and work.(When monitor and camera both have Low power
module.)
3.6V/6400mAh
DC 5-12V
5V/8 hrs, 12V/3hrs
12 continuous hours
0-40°C
IP69K
1/3" CMOS
1920 x 1080 Pixels
4.80mm x 3.73mm
2403-2478 MHz
300m
130 m/s
8 to 10 meters
Yes
130°
Yes
30 seconds of inactivity
60 lbs
Operating Instructions
EC2030-WC2 Wireless Camera
Pairing Instructions:
Using the EC7008-WM2 monitor:
1. Press 'M' to show menu.
2. Press '+' or '-' button to select Pairing menu.
3. Press ▼ to enter Pairing menu.
4. Select the camera channel you want to pair by using '+' or '-' button.
5. Press ▼ to start pairing. A PAIRING symbol will show. Power on the camera
within the first 15 seconds. Pairing will fail if no camera is detected in 20 seconds.
6. The camera will pair with the monitor after 5-8 seconds.
Using EC7008-WM2 remote:
1. Press SEL to enter the single camera mode and camera image number to be
paired.
2. Press PAIR to enter the PAIRING OPTION.
3. The monitor will display the pairing menu, with a PAIRING symbol shown above
the currently selected camera. Power on the camera within the first 15 seconds.
Pairing will fail if no camera is detected in 20 seconds.
4. The camera will pair with the monitor after 5-8 seconds.
ON/OFF
FIGURE 1
Page 1 of 2