Poulan LE Serie Manual De Instrucciones página 5

Symmetrical Guide Bar _._'_4_
large Radius Tip
• Low-Kickback Chain, designed with a
contoured deNh gauge and guard link
which deflect kickback force and allow
wood 1o grad ually ride into the cutter. Low-
Kickback Chain has met kickback per-
formance requirements when tested on a
representative sample of chain saws be-
low 3.8 cubic inch displacement specified
in ANSI Bt75.f.
Contoured Depth Gauge
_[k Elongated GuardLink
Deflects
iekbackforce
Low-Kickback
'_ and a_lows wood
Chain to gradually ride
Info cutter
_Oan Obstruct Material
Not a Low-Kickback Chain
• Front Hand Guard, designed to reduce the
chance of your left hand contacting the chain
if your hand slips off the front handlebar.
• Position of front and rear handlebars, de-
signed with distance between handles and
"in-line" with each other The spread and
"in-line" position of the hands provided by
this design work together to give balance
and resistance in controlling the pivot of
the saw back toward the operator if kick-
back occurs.
CHAIN BRAKE AND CKA ANGLE
• Chain Brake, designed to stop the chain in
the event of kickback.
_I_WARNING:
WE DO NOT REP-
RESENT AND YOU SHOULD NOT AS-
SUME THAT THE CHAIN BRAKE WILL
PROTECT YOU IN THE EVENT OF A
KICKBACK. Kickback is a lightning fast ac-
tion which throws the bar and rotating chain
back and up toward the operatoE Kickback
can be ca used by allowing contact of the bar
tip in the danger zone with any hard object.
Kickback can also be caused by pinching the
saw chain along the top ofthe guide bar. This
Computed kickback an£11e (CKA) Table
BAR
MODEL P/N Length
2250 LE 952044368 14"
2250LE/2450 LE 952044970 16"
2550 LE 952044418 18"
action may push the guide bar rapidly back
toward the operator. Either of these events
may cause you to lose controt of the saw
which could result in serious injury or even
death. DO NOT RELY UPON ANY OF THE
DEVICES BUILT INTO YOUR SAW. YOU
SHOULD USE THE SAW PROPERLY AND
CAREFULLY TO AVOID KICKBACK. Re-
duced-kickback guide bars and low-kick-
back saw chains reduce the chance and
magnitude of kickback and are recom-
mended. Your saw has a low kickback chain
and bar as original equipment. Repairs on a
chain brake should be made by an autho-
rized servicing dealer. Take your unit to the
place of purchase if purchased from a ser-
vicing
dealer,
or to the nearest
authorized
master service dealer.
• T_pcontact in some cases may cause a light-
ning fast reverse REACTION, kicking the
guide bar up and back toward the operator.
• Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back toward the operator.
• Either of these reactions may cause you to
lose controt of the saw which could result
in serious injury.Do not rely exclusively
upon the safety devices built into your saw.
,1_ WARNING:
Computed kickback
angle (CKA) listed on your saw and listed in
the CKA table below represents angie of
kickback your bar and chain combinations
will have when tested in accordance with
CSA and ANSI standards. When purchasing
replacement bar and chain, considerations
should be given to the lower CKA values.
Lower CKA values represent safer angles to
the user, higher values indicate more angle
and higher kick energies. Computed angles
represented in the non-activated cotumn in-
dicate total energy and angle associated
without activation of the chain brake during
kickback. Activated angle represents chain
stopping time relative to activation angle of
chain brake and resulting kick angle of saw.
In all cases lower CKA values represent a
safer operating environment for the user.
The following guide bar and chain combina-
tions meet kickback requirements of CSA
Z62.1, Z62.3, & ANSI B175.1 when used on
saws listed in this manual. Use of bar and
chain combinations other than those listed is
not recommended and may not meet the
CKA requirements per standard.
CHAIN P/N CKA without chain brake
952051209 24 °
952051211 19 °
952051338 14 °