Weed Eater SB180BV Manual Del Operador página 3

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

MAINTAIN
YOUR
UNIT PROPERLY
• Have all maintenance
other than the rec-
ommended
procedures
described
in the
Operator's
Manual
performed
by your
Service Dealer.
• Disconnect
spark plug before performing
maintenance
except for carburetor adjust-
ments.
• Use only recommended
WEED
EATER
replacement
parts; use of any other parts
may void your warranty and cause dam-
age to your unit.
• Empty the fuel tank before storing the unit.
Use up fuel left in carburetor by starting the
engine and letting it run until it stops.
• Do not use any accessory
or attachment
other than
those
recommended
by the
manufacturer
for use with your unit.
• Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from water heaters,
electric
motors or switches, furnaces, etc.
• Store in a dry area out of reach of children.
SPECIAL
NOTICE:
For users on U.S.
Forest Land and in some states,
including
California(Public
Resources
Codes
4442
and 4443), Idaho, Maine, Minnesota,
New
Jersey, Oregon, and Washington:
Certain in-
ternal combustion
engines operated
on for-
est, brush, and/or grass covered land in the
above areas are required to be equipped
with a spark arrestor, maintained
in effective
working order, or the engine must be con-
structed,
equipped,
and maintained
for the
prevention
of fire. Check with your state or
local authorities
for regulations
pertaining to
these requirements.
Failure to follow these
requirements
is a violation of the law. This
unit is not factory equipped with a spark ar-
restor; however, a spark arrestor is available
as an optional
part. If a spark arrestor is re-
quired in your area, contact your Authorized
Service Dealer for the correct kit. The spark
arrestor, blower tubes, and nozzles must be
assembled to the unit to be in full compliance
with the regulations.
SPECIAL
NOTICE:
Exposure
to vibra-
tions through
prolonged
use of gasoline
powered hand tools could cause blood ves-
sel or nerve damage
in the fingers, hands,
and joints of people prone to circulation
dis-
orders or abnormal swelling. Prolonged use
in cold weather has been linked to blood ves-
sel damage in otherwise
healthy people. If
symptoms
occur such as numbness,
pain,
loss of strength, change in skin color or tex-
ture, or loss of feeling in the fingers, hands, or
joints, discontinue
the use of this tool and
seek medical attention. An antivibrafion
sys-
tem does not guarantee
the avoidance
of
these problems.
Users who operate power
tools on a continual and regular basis must
monitor closely their physical condition
and
the condition of this tool.
PREPARATION
_ib WARNING:
Stop the engine and be
sure the impeller blades have stopped turn-
ing before opening the vacuum inlet door or
attempting
to insert or remove the vacuum
tubes. The rotating blades can cause seri-
ous injury.
_kWARNING:
If you receive your unit
assembled,
check each step to insure your
unit is properly assembled.
Follow all safety
information
in the manual and on the unit.
BLOWER
TUBE ASSEMBLY
• Assemble
the blower tube and nozzle to
the unit (turn clockwise to tighten).
SHOULDER
STRAP
ASSEMBLY
(for
blower
use
only)
• Pass the shoulder
strap over your head
and onto your left shoulder.
• Snap the hook onto the retainer on the top
handle.
_
Retainer
VACUUM
BAG ASSEMBLY
• Open the zipper on the vacuum bag and in-
sert the elbow tube.
• Push the end of the elbow tube with the
grooves through the small bag tube open-
ing. Make sure the bag tube opening
is
flush against large raised rib on the tube.
• Close the zipper on the bag. Make sure the
zipper is closed completely
and the zipper
seam is tucked toward inside of the bag.
Raised Rib_
_Bag
Tube
f_
Opening
Zippe[
[
-3-
Tabla de contenido
loading

Tabla de contenido