Idiomas disponibles
Idiomas disponibles
feaTures
• New reinforced ergonomic shift knob design makes changing from forward to reverse easy.
• New added bearings on both sides of the gearing increases durability, tool life, as well as cuts
down on internal friction allowing the tool to run smoother.
• Rapid response variable speed trigger allows for one finger operation and unmatched control.
• Rotating side exhaust allows user to direct air away from work.
• One of the most powerful 1/2" ratchets on the market with 130 ft. lbs. of torque.
• Matco patented captured head and grease fitting.
aIr suPPly
Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure measures 90 psig at the tool with
the trigger fully depressed and no load applied to the tool. Higher
pressure and unclean air will shorten tool life and may create a
hazardous condition.
Water in the air line will cause damage to the tool. Drain water
from air lines and compressor prior to running tool. Clean the air
inlet filter screen weekly. The recommended hook-up procedure
can be viewed in Figure 1.
The air inlet (Figure 2), used for connecting air supply, has
standard 1/4" NPT American Thread.
Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet). Minimum hose diameter should be
3/8" I.D. and fittings should have the same inside dimensions.
Ensure an accessible emergency shut off valve has been installed in
the air supply line and make others aware of its location.
TrOuBleshOOTIng
Other factors outside the tool may cause loss of power or erratic
action. Reduced compressor output, excessive drain on the air line,
Whip Hose
Do Not Install
Quick Coupling
Nipple
Here
Leader
Quick Coupler
Hose
WarranTy
Matco warrants this air tool for a period of 1 year to the consumer.
We will repair any MT Series air tool covered under this warranty
which proves to be defective in material or workmanship during
the warranty period. In order to have your tool repaired, return
the tool to any of the Matco Authorized Warranty Centers listed,
freight prepaid. Please include a copy of your proof of purchase
and a brief description of the problem. The tool will be inspected
and if any part or parts are found to be defective in material
or workmanship, the tool will be repaired free of charge and
returned to you freight prepaid.
This warranty gives you specific rights. You may also have other
rights which vary from state to state.
The foregoing obligation is Matco's sole liability under this or any
implied warranty and under no circumstances shall Matco be
liable for any incidental or consequential damages.
MT2859
MT2859 1/2" Heavy Duty Air Ratchet
Air Supply
Filter
Nipple
Oiler
Regulator
Drain Daily
moisture or restrictions in air pipes or the use of hose connections
of improper size or poor conditions may reduce air supply. If
outside conditions are in order, and the tool still performs
erratically, disconnect tool from hose and take tool to your
nearest Matco authorized service center.
luBrIcaTIOn & MaInTenance
Lubricate the tool daily with a high quality grade of air tool oil. If no
air line oiler is used, run 1/2 ounce of oil through the tool. The oil
can be squirted into the tool air inlet Figure 2, or into the hose at
the nearest connection to the air supply, then run the tool. A rust
inhibitive oil is acceptable for air tools. Grease fitting on yoke and
ratchet housing occasionally to ensure proper lubrication of the
ratchet mechanism.
WARNING
After an air tool has been lubricated, oil will discharge through
the exhaust port during the first few seconds of operation. The
exhaust port must be covered with a towel before applying air
pressure to prevent serious injury.
TrIgger
fIg. 1
Note: Some states do not allow the exclusion or limitation of
incidental or consequential damages so the above limitation or
exclusion may not apply to you.
naTIOnal MachIne grOuP
aIr TOOl rePaIr cenTer
1330 Commerce Dr.
Stow, OH 44224
(330) 688-6494
dIscOunT TOOl rePaIr
3433 Losee Rd. #1
North Las Vegas, NV 89030
(702) 657-6570
hT PneuMaTIc reBuIlders
22 Goodmark Place Unit #8
Toronto, ON M9w 6R2
(416) 213-0172
3
fOrWard/reVerse
aIr InleT
fIg. 2
rev. 07/08/14
