Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
WARNING!
Failure to install or use this product according to manufacturer's recommendations may result in property damage, serious injury, and/
or death to those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understood the safety information
contained in this manual.
1.
Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to
ensure the safety of emergency personnel and the public.
2.
Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical
connections.
3.
This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including fire.
4.
Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of
the system is maximized and the controls are placed within convenient reach of the operator so that they can operate the system without
losing eye contact with the roadway.
5.
Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag
deployment area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death.
Refer to the vehicle owner's manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable
mounting location ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6.
It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors),
people, vehicles or other obstructions.
7.
The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal.
Never take the right-of-way for granted. It is the vehicle operator's responsibility to be sure they can proceed safely before entering an
intersection, drive against traffic, respond at a high rate of speed, or walk on or around traffic lanes.
8.
This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws
regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The
manufacturer assumes no liability for any loss resulting from the use of this warning device.
Specifications
Weight:
Input Voltage:
Input Current:
Output Power:
Fusing Requirement:
Matrix
Connectivity:
®
Operating Temperature:
5.2lbs
12-24 VDC
6.8 A max.
87.0 W max.
10A
CAT5
-40ºC to 65ºC
(-40ºF to 149ºF)
Installation and Operation Instructions
Thin WingMan Series
MATRIX
Enabled
®
Page 1 of 8
loading

Resumen de contenidos para Code 3 MATRIX Thin Wingman Serie

  • Página 1 Installation and Operation Instructions Thin WingMan Series MATRIX Enabled ® IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user. WARNING! Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious injury, and/ or death to those you are seeking to protect! Do not install and/or operate this safety product unless you have read and understood the safety information contained in this manual.
  • Página 2 Carefully remove the product and place it on a flat surface. Examine the unit for transit damage and locate all parts. If damage is found or parts are missing, contact the transit company or Code 3. Do not use damaged or broken parts.
  • Página 3 Wiring Instructions: IMPORTANT! This unit is a safety device and it must be connected to its own separate, fused power point to assure its continued operation should any other electrical accessory fail. Notes: Larger wires and tight connections will provide longer service life for components. For high current wires it is highly recommended that terminal blocks or soldered connections be used with shrink tubing to protect the connections.
  • Página 4 The Matrix network is designed to accommodate a large number of accessory devices. However, Matrix enabled Thin WingMan utilizing ® ® CAT5 will always be the last device in either the PRI-1 or SEC-2 chain. Further instructions, features, and control options are detailed in the installation manual of the customer selected “Central Node”.
  • Página 5 Flash Pattern Compliance Chart - Tri Color SAE J595 CA TITLE 13 Description Amber Amber Amber Amber Blue White Blue Color 1&2 Color 3 Color 1&2 Color 3 Single CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS B CLASS B CLASS B Single 90-300 Single (ECE R65)
  • Página 6 Replacement Parts: Description Part No. Gaskets Replace Thin WingMan Gasket CZ4103 Troubleshooting: All lightbars are thoroughly tested prior to shipment. However, should you encounter a problem during installation or during the life of the product, follow the guide below for troubleshooting and repair information. If the problem cannot be rectified using the solutions given below, additional information may be obtained from the manufacturer –...
  • Página 7 Notes: Page 7 of 8...
  • Página 8 *Code 3®, Inc. reserves the right to repair or replace at its discretion. Code 3®, Inc. assumes no responsibility or liability for expenses incurred for the removal and /or reinstallation of products requiring service and/or repair.;...
  • Página 9 Instrucciones de instalación y operación Serie Thin Wingman MATRIX activado ® ¡IMPORTANTE! Lea todas las instrucciones antes de instalar y utilizar. Instalador: Este manual se debe entregar al usuario final. ADVERTENCIA Si este producto no se instala o se utiliza de acuerdo con las recomendaciones del fabricante, esto podría tener como resultado daños a la propiedad, lesiones graves o la muerte de las personas que se busca proteger.
  • Página 10 Retire el producto con cuidado y colóquelo sobre una superficie plana. Examine la unidad en busca de daños que se hayan producido en el transporte y localice todas las piezas. Si encuentra algún daño, o faltan piezas, comuníquese con la empresa de transporte o Code 3. No utilice piezas dañadas o rotas.
  • Página 11 Instrucciones de cableado: ¡IMPORTANTE! Esta unidad es un dispositivo de seguridad y se debe conectar a su propia fuente de poder de fusibles separada para asegurar su funcionamiento continuo si cualquier otro accesorio eléctrico falla. Notas: Los cables más largos y las conexiones bien ajustadas ofrecerán una mayor vida útil a los componentes. Para cables de alta corriente, se recomienda usar bloques de terminales o conexiones soldadas cuando se intube por contracción para proteger las conexiones.
  • Página 12 La red Matrix está diseñada para alojar un gran número de dispositivos accesorios. Sin embargo, un Thin WingMan compatible con ® Matrix que utilice CAT5 siempre será el último dispositivo en la cadena PRI-1 o SEC-2. En el manual de instalación del "nodo central" ®...
  • Página 13 Solución de problemas: Todas las barras de luces se prueban a fondo antes de su envío. Sin embargo, si se produce un problema durante la instalación o durante la vida útil del producto, siga la guía que aparece a continuación para obtener información sobre la solución de problemas y la reparación. Si el problema no se puede solucionar con las soluciones que se indican a continuación, puede obtener información adicional del fabricante;...
  • Página 14 Asegúrese de utilizar suficientes materiales de embalaje para evitar que se dañe el producto durante el envío. * Code 3®, Inc. se reserva el derecho a realizar reparaciones o reemplazar productos según su criterio. Code 3®, Inc. no asume responsabilidad alguna por los gastos efectuados para remover o reinstalar los productos que requieren servicios o reparaciones, por el embalaje, la manipulación y el envío ni por la manipulación de los productos devueltos al remitente después de que se haya prestado el servicio.