Alarms (Reference Table) - Elledi STAR 10.2 C Manual De Uso Y Mantenimiento

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

Alarms (reference table)

CODE
CODE
TITLE
TITLE
AL 01
AL 01
BLACK OUT
BLACK OUT
AL 02
AL 02
SMOKE SENSOR
SMOKE SENSOR
AL 03
AL 03
SMOKE OVERTEMP.
SMOKE OVERTEMP.
EXTRACTOR MALFUNCTION-
EXTRACTOR MALFUNCTION-
AL 04
AL 04
ING
ING
AL 05
AL 05
START-UP FAILURE
START-UP FAILURE
AL 06
AL 06
PELLET FINISHED
PELLET FINISHED
SAFETY THERMAL SWITCH
SAFETY THERMAL SWITCH
AL 07
AL 07
WITH MANUAL RE-ARM
WITH MANUAL RE-ARM
AL 08
AL 08
DEPRESSION
DEPRESSION
! IMPORTANT
Position
protected by the screw cap, for
the safety reset thermostat on
the back of the stove.
STAR 10.2 C- STAR 12.2 C
Use and maintenance manual
- Missing voltage during the work phase
- Missing voltage during the work phase
- The smoke sensor is malfunctioning
- The smoke sensor is malfunctioning
- The smoke sensor is disconnected from the
- The smoke sensor is disconnected from the
electronic board
electronic board
- Combustion in the brazier is not optimal
- Combustion in the brazier is not optimal
due to clogging in the brazier or within
due to clogging in the brazier or within
internal stove passages
internal stove passages
- The centrifugal fan (if present) is
- The centrifugal fan (if present) is
defective or damaged
defective or damaged
- Encoder smoke extractor not working or not
- Encoder smoke extractor not working or not
connected correctly
connected correctly
- No power to the smoke extractor
- No power to the smoke extractor
- The smoke extractor is blocked
- The smoke extractor is blocked
- The pellet tank is empty
- The pellet tank is empty
- Pellet calibration and suction during the
- Pellet calibration and suction during the
ignition phase is unsuitable.
ignition phase is unsuitable.
- The resistance for ignition is defective or not
- The resistance for ignition is defective or not
in position
in position
- The pellet tank is empty.
- The pellet tank is empty.
- The motor reducer is not loading the pellet
- The motor reducer is not loading the pellet
- Lack of pellet load
- Lack of pellet load
- The manual re-arm thermostat
- The manual re-arm thermostat
connected to the hopper has tripped
connected to the hopper has tripped
- Combustion in the brazier is not optimal
- Combustion in the brazier is not optimal
due to clogging in the brazier or within
due to clogging in the brazier or within
internal stove passages.
internal stove passages.
- The chimney is blocked.
- The chimney is blocked.
- The vacuum state is malfunctioning.
- The vacuum state is malfunctioning.
EVERY ALARM CONDITION CAUSES THE STOVE TO SWITCH OFF IMMEDIATELY. PRESSING THE P3 KEY
ON THE SCREEN FOR A FEW SECONDS, THE ALARM MAY BE CANCELLED.
of
the
switch,
REASON
REASON
RESOLUTION
RESOLUTION
- Press the shut-off key and repeat
- Press the shut-off key and repeat
stove start-up
stove start-up
- If the problem remains, contact After-Sales
- If the problem remains, contact After-Sales
Service.
Service.
- Contact After-Sales Service
- Contact After-Sales Service
- Contact After-Sales Service
- Contact After-Sales Service
- Shut-off the stove, clean the brazier, use the
- Shut-off the stove, clean the brazier, use the
pipe unit cleaning and finally adjust the
pipe unit cleaning and finally adjust the
combustion using the Pellet/Air setting
combustion using the Pellet/Air setting
- Contact After-Sales Service
- Contact After-Sales Service
- If the problem remains, contact After-Sales
- If the problem remains, contact After-Sales
Service.
Service.
- Contact After-Sales Service
- Contact After-Sales Service
- Contact After-Sales Service
- Contact After-Sales Service
- Contact After-Sales Service
- Contact After-Sales Service
- Verify pellet presence in the tank.
- Verify pellet presence in the tank.
Load if needed.
Load if needed.
- Contact After-Sales Service
- Contact After-Sales Service
- Contact After-Sales Service
- Contact After-Sales Service
- Verify pellet presence in the tank.
- Verify pellet presence in the tank.
Load if needed
Load if needed
- Empty the tank to verify that
- Empty the tank to verify that
inside there are no fallen objects that
inside there are no fallen objects that
may prevent correct
may prevent correct
auger operation.
auger operation.
- Adjust the pellet set from "SET ARIA/PELLET"
- Adjust the pellet set from "SET ARIA/PELLET"
(Air/Pellet Set)
(Air/Pellet Set)
- If the problem remains, contact After-Sales
- If the problem remains, contact After-Sales
Service
Service
- Re-arm the thermostat by pressing the button
- Re-arm the thermostat by pressing the button
on the
on the
back of the stove.
back of the stove.
- Shut-off the stove, clean the brazier, use the
- Shut-off the stove, clean the brazier, use the
pipe unit cleaning and finally adjust the
pipe unit cleaning and finally adjust the
combustion using the Pellet/Air setting
combustion using the Pellet/Air setting
- Contact After-Sales Service
- Contact After-Sales Service
- Verify that the chimney is free and
- Verify that the chimney is free and
clean.
clean.
- Contact After-Sales Service
- Contact After-Sales Service
Rev.1 03/08/2017
Page 55

Hide quick links:

Tabla de contenido
loading

Este manual también es adecuado para:

Star 12.2 cStar 10.2 c

Tabla de contenido