Rockford Fosgate 3SIXTY RFBLD Manual De Instrucciones

SPECIFICATIONS
Operating Voltage:
Idle Current:
Frequency Response:
CMRR (Common Mode Rejection Ratio):
Channel Separation:
Output Impedance:
Input Impedance:
Gain:
"A" Weighted Signal to Noise Ratio @ 2V:
"A" Weighted Signal to Noise Ratio @ 10V: >/= 110 dB
THD+N:
Recommended Fuse Rating:
Dimensions: Width – 5.90" (150.0mm)
Height –1.32" (33.5mm)
Depth – 4.09" (103.8mm)
FEATURES
2 Channel
Low Output Impedance
Selectable Balanced Differential or Single Ended
Inputs and Outputs
High-Voltage Line Driver
11 Vrms Unbalanced
22 Vrms Balanced
Output Level Indicators
Speaker Level to RCA Line Level Converter
Remote Voltage Out Function When Utilizing
High Level Inputs
Superior Low Distortion, Low Noise Operation
LINE DRIVER FEATURES
TOP
1
INPUT
3 4 5
OUTPUT
8
1. Voltage Indicators – Visual aid for the adjusting
the input voltage to your amplifier utilizing the
Gain adjuster.
2. Power Indicator – Lights up Blue when power
is on.
3. Gain Adjuster – Used for adjusting the input
voltage to your amplifier.
4. High Level Input – Input from source utilizing
High Level (speaker line) connection.
5. RCA Inputs – Input from source utilizing RCA
line connection.
9-16 VDC
300 mA
20-50k Hz +/- 1 dB
>/= 70 dB
>/= 80 dB
55 Ohms
20k Ohms
+0.8 dB - +24 dB
>/= 90 dB
0.01%
1A
B a l a n c e d
6. Input Balanced/Unbalanced Swith – Selectable
to switch between balanced and unbalanced input
connection from source.
2
7. Power Connection – 12V DC connection to
power line driver, with remote turn-on.
8. RCA Outputs – Output to amplifier utilizing RCA
line connection.
9. Output Balanced/Unbalanced Swith –
Selectable to switch between balanced and
unbalanced output connection to amplifier.
INSTALLATION
CAUTION: If you feel unsure about installing
6 7
CAUTION: Before installation, disconnect the
9 CAUTION: Avoid running power wires
Power Connection
1. Connect a wire from a constant 12 volt DC source
to the first (B+) terminal on the power connector.
Tighten the set screw to secure the wire in place.
NOTE: If you are connecting directly to the battery,
L i n e D r i v e r
R F B L D
Rockford Fosgate
Rockford Corporation
546 South Rockford Drive
Tempe, Arizona 85281 U.S.A.
In U.S.A., (480) 967-3565
Customer Service 1-800-669-9899
www.rockfordfosgate.com
this system yourself, have it
installed by a qualified Rockford
Fosgate technician.
battery negative (-) terminal to
prevent damage to the unit, fire
and/or possible injury.
near the low level input cables,
antenna, power leads, sensitive
equipment or harnesses.The
power wires carry substantial
current and could induce noise
into the audio system.
ensure the wire is equipped with a fuse. See
specifications for fuse rating.
LIMITED WARRANTY
The RFBLD (Balanced Line Driver) has a warranty of
1 Year.This warranty covers only the original purchaser
of Rockford product purchased from an Authorized
Rockford Fosgate Dealer in the United States. In order to
receive service, the purchaser must provide Rockford with
a copy of the receipt stating the customer name, dealer
name, product purchased and date of purchase.
Products found to be defective during the warranty period
will be repaired or replaced (with a product deemed to be
equivalent) at Rockford's discretion.
What is Not Covered
1. Damage caused by accident, abuse, improper operations,
water, theft, shipping
2.Any cost or expense related to the removal or reinstalla-
tion of product
3. Service performed by anyone other than Rockford or an
Authorized Rockford Fosgate Service Center
4.Any product which has had the serial number defaced,
altered, or removed
5. Subsequent damage to other components
Limit on Implied Warranties
Any implied warranties including warranties of fitness for use
and merchantability are limited in duration to the period of
the express warranty set forth above. Some states do not
allow limitations on the length of an implied warranty, so this
limitation may not apply. No person is authorized to assume
for Rockford Fosgate any other liability in connection with
the sale of the product.
How to Obtain Service
Contact the Authorized Rockford Fosgate Dealer you
purchased this product from.
If you need further assistance, call 1-800-669-9899 for
Rockford Customer Service.
09/08 Printed in China
2. Connect a wire from a clean chassis ground point to
the last (GND) terminal on the power connector.
Tighten the setscrew to secure the wire in place.
NOTE: Keep the length of the Ground wire (GND) as
short as possible.
3. Insert a wire into the middle (REM) terminal on
the power connector and tighten the setscrew to
secure the wire in place.
Used as an input: Connect the other end of the
REM wire to a switched 12 volt positive source.The
switched voltage is usually taken from the source
unit's remote amp on lead.
Used as an output: This feature only functions if
the Line Driver is connected to the source unit
using the HIGH LEVEL inputs. Connect the other
end of the REM wire to the Remote ON input of
an external device, such as an amplifier.We
recommend using this feature only if the vehicle
source unit does not have a remote output to turn
on external devices.
IMPORTANT: When used, the remote out is current
limited.We recommend using a relay if
you need to remotely turn on more
than two (2) other devices.
Connector
Strip 1/4"
(0.25)
Power B+
(6.4mm)
1230-54757-01
Ground
Remote