ProBreeze PB-10 Manual De Instrucciones página 5

CONTROL PANEL
― ―
1 2
7 8
1. Timer Indicator Light
2. Mode Indicator Light
3. Room Humidity Indicator Light
4. Humidity Setting Indicator Light
5. Water Tank 'Full' Indicator Light
OPERATING INSTRUCTIONS
― ―
Turning On and Off:
• Press the power button once to turn the appliance on or off.
• When turning on, the appliance will function with the last settings selected.
• When turned off the fan will continue to run for 2 minutes to help cool and protect the
internal components.
Setting a Timer:
• Press the Timer button to cycle through the timer options of 2 hours, 4 hours, 8 hours, 12
hours, or no timer.
• The selected timer indicator light will turn on. As the remaining time decreases, the timer
indicator lights indicating how much time is left will turn on.
Setting the Mode:
Press the Mode button to cycle through the mode options.
• AUTO: The dehumidifier automatically adjusts between high and low modes depending on
the humidity of the room, and your desired humidity level.
• LOW: The dehumidifier runs with a low fan speed and a low heater setting.
• HIGH: The dehumidifier runs with a high fan speed and a high heater setting.
Note: The display will revert to showing the room's current humidity level 3 seconds after you
select a setting.
8 of 88 | English
3 4 5 6
9 10
6. 'Check' Indicator Light
7. Timer Button
8. Mode Button
9. Humidity Setting Button
10. Power Button
Setting the Humidity:
Press the Humidity Setting Button to cycle through the humidity setting options.
• At 40% humidity, the 40% humidity indicator light will turn on.
• At 45% humidity, the 40% and 50% humidity indicator lights will turn on.
• At 50% humidity, the 50% humidity indicator light will turn on.
• At 55% humidity, the 50% and 60% humidity indicator lights will turn on.
• At 60% humidity, the 60% humidity indicator light will turn on.
When desired humidity is greater than actual room humidity, the Humidity Indicator Light will
flash, and the dehumidifier will enter energy saving standby mode. When in standby mode, the
heater will stop and the air outlet will stop. The fan will continue to operate for two minutes to
cool the dehumidifier. After 30 minutes in standby mode, the fan will switch on for five minutes
to check the humidity of the room. If the room humidity has not increased by more than 5%
of desired humidity, the dehumidifier will return to standby mode. Once the room humidity
increases by more than 5% of desired humidity, the dehumidifier will automatically restart and
return to operation.
Current Room Humidity % RH is displayed by the Room Humidity Indicator Lights. E.g. if the room
humidity is 40% RH one light will illuminate next to 40%. If the room humidity is 45% RH two lights
will illuminate, one next to 40% and one next to 50%.
CONNECTING THE WATER HOSE FOR CONTINUOUS DRAINING
― ―
For long-term use, it is recommended to connect a hose
for continuous drainage.
To attach the hose:
1. Use a screwdriver or similar tool to remove the plastic
covering from the continuous drainage hole at the
back of the dehumidifier.
2. Check that the water tank is securely in position.
3. Insert the hose into the water hose connector and
check it is connected properly. (12mm)
REMOVING AND EMPTYING THE WATER TANK
― ―
When the water tank is full three beeps will sound; the Water Tank Full Indicator Light will
continuously flash and the dehumidifier will pause operation to prevent the water tank from
overflowing. To remove and empty the water tank:
1. Turn off the dehumidifier, wait two minutes for the fan to stop, and unplug it from the wall
socket.
2. Gently pull the water tank out from the front of the dehumidifier.
3. Use handle to empty the water tank.
4. Once empty, slot the tank back in carefully.
English | 9 of 88