Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
iSND1W
EN
iSND1W – Mono Wi-Fi and Bluetooth
Surround sound
Features:
•
15W R.M.S.
•
Audio stream
•
Bluetooth audio
Applications:
•
Surround sound
ISND1W
https://
mordomus.com/
mordomus/
docs/wifi/
iSND1W.pdf
Electrical Specifications:
Power supply voltage: 15VDC
Consumption: 1A @ 15VDC
Output power: 15W R.M.S.@4Ohms (15VDC)
Idle Channel Noise = 45uVRMS (A-Wtd)
THD+N: 0.04% (at 1 W, 1 kHz)
Storage Temperature: -10ºC to 60ºC
Operating Temperature: 10ºC to 50ºC
Maximum humidity: 80% non-condensing
Speaker Impedance: 4 to 8 Ohm
Wireless standards: WI-FI 2,4GHz 802.11 b/g/n, Bluetooth v4.2 BR/EDR
Maximum supported stream bitrate: 320kbps
Bluetooth Audio format: SBC
Physical Specifications:
Dimensions: 54mm X 86mm X 25mm.
Protection degree: IP20, for indoor use.
ATTENTION:
Mordomus shall not be liable for any damages resulting from the
use of our equipment outside the specifications and/or for a purpose
other than that intended.
When connecting speakers in parallel, make sure that the total
impedance is not inferior to 4 Ohm.
Do not connect speakers with less than 4 Ohm impedance.
Assure Wi-Fi signal strength of at least 2 bars.
Use only the supplied mains adapter.
Overview:
Speaker output connector
Push-button for configuration
Power Supply (15V 1A)
Connection status indicator
1. Installation
Caution! Before installing the device, make sure that the mains power
is turned off.
1. Disconnect from mains power.
2. Perform the connections according to the schematic.
3. Power up.
2. Connection to WI-FI network and enrollment to Mordomus
Method 1 - Automatic Setup (Router must support WPS)
1. Since factory, on powering up the iSND1W is in WPS negotiation mode
signaled by the connection status indicator blinking fast continuously.
Take care not to power up more than one iSND1W device at the same
time since WPS allows for configuration of only one device at a time. We
recommend powering up and registering the devices in a sequential manner.
2. Press the WPS button on the router according to the user manual of this
device and wait until the WPS negotiation is completed. This is signaled by 2
short blinks of the connection status indicator every 2 seconds.
3. Activate the pairing mode in the Mordomus Software by clicking the Start
inclusion button in the device registration menu.
To reach this menu from the main screen click Configurations →
v.2311
1/7
Manuales relacionados para MORDOMUS TRUE IOT iSND1W
Resumen de contenidos para MORDOMUS TRUE IOT iSND1W
- Página 1 15W R.M.S. • Audio stream • Bluetooth audio 3. Activate the pairing mode in the Mordomus Software by clicking the Start Applications: inclusion button in the device registration menu. • Surround sound To reach this menu from the main screen click Configurations →...
- Página 2 2 seconds. 2. Enter the (SSID) in the field WiFi Name and password WiFi password. Enter the Mordomus Home Name in the field Home Name as defined in Mordomus - > Configurations -> Connectivity: Mordomus Home Name.
- Página 3 A Mordomus não se responsabiliza por quaisquer danos resultantes do uso dos nossos equipamentos fora das especificações e/ou para Ao introduzir o nome da sua casa, os campos Mordomus local IP e uma finalidade diferente da prevista. Mordomus Port devem ser deixados em branco.
- Página 4 • Sonorización ambiente Especificaciones eléctricas: 3. Active el modo de emparejamiento en el software Mordomus haciendo clic en Voltaje de la fuente de alimentación: 15 VDC el botón Iniciar la inclusión... en el menú de registro del dispositivo. Consumo: 1A @ 15VDC Para acceder a este menú...
- Página 5 1.Toque y mantenga presionado el botón del iSND1W durante al menos Ingrese el Nombre de la casa Mordomus en el campo Home Name como se 12 segundos para activar el modo Punto de acceso. Esto se indica mediante 3 define en Mordomus -> Configuraciones -> Conectividad: Nombre de inicio parpadeos breves del indicador de estado de la conexión cada 2 segundos.
- Página 6 Assurez-vous que la force du signal Wi-Fi est d'au moins 2 barres. Utilisez uniquement l'adaptateur secteur fourni. En entrant le nom de la maison, les champs Mordomus local IP et Mordomus Port doivent rester vides. Vue d'ensemble: 3. Activez le mode de couplage dans le logiciel Mordomus en cliquant sur le Connecteur de sortie audio bouton Commencer l'inclusion dans le menu d'enregistrement de l'appareil.
- Página 7 5.1. Page de configuration La page de configuration de l’iSND1W permet une configuration manuelle de: WiFi Name WiFi Password Mordomus Home Name Mordomus Local IP Mordomus port Le bouton Reset all réinitialise tous les paramètres ci-dessus et les autres configurations aux valeurs d'usine.