GE 20108 Manual De Instrucciones

GE Branded Christmas Trees
Easy Light Technology
eliminates cord connections
Warm White 2 Way Chasing
Use the foot pedal to change functions
Assembly Instructions
Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas
tree. Should you have any problems with your tree, visit us at
www.geholidaylighting.com
toll free number at 1-877-398-7337.
Check our website for latest service hours and assembly instruction videos.
1. Carefully unpack, removing any bubble wrap and inspect the
contents of your tree. {Fig. A}
A
A
The tree stand should be open and set at a 90
angle. Remember to tighten the thumbscrew after
connecting section A and tree stand. See {Fig. B}
Untwist the red metal tie wrap holding the
branches in place.
Gently position any branches that do not fall
into place.
C
NOTE: No tools required
Tree Sections
7.5 ft tree 3
* Does not include time for shaping branches, estimated shaping time is 30 minutes/section.
DISCLAIMER
: DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS
LIGHTING OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB
SOCKET. DOING THIS MAY RESULT IN DAMAGE TO YOUR CHRISTMAS
TREE OR CAUSE PERSONAL INJURY. DOING THIS, WILL RESULT IN A
VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.
Disconnect the decorative item from the power source before
performing any maintenance or cleaning.
For indoor use only
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
GE is a trademark of General Electric Company
and is under license by Nicolas Holiday Ltd.
©2020 Nicolas Holiday Ltd.
9 F., No. 37, Guangfu North Rd.,
Taipei, Taiwan 10560 All rights reserved.
20108LO
Printed in China
8.25"x11.25"
®
for more information. You can call our
B
B
90
Thumbscrew
2. When you connect two tree sections,
it is important that you align the mark
on the tree poles. See {Fig. C}
Tree Stand Approx. Asm Time *
Metal 10 – 15 minutes
120V
TREE ASSEMBLY DIAGRAM
TOP
B
A
TOP
SCHEMATIC DIAGRAM
3. Assemble section by section. Firmly seat both sections together.
Note:
a. Always unplug this product before installing.
Do not plug in tree to a power outlet until the entire tree is assembled.
b. This tree is provided with an extension cord for a tree topper, which can be
attached to the top section along the pole.
c. As an option, the tree adapter can be plugged into the back of the tree top
extension cord as an add-on. This feature allows you to utilize only one outlet.
4. To change functions,
step on the foot pedal
to the desired function
as listed on the back
of the foot pedal.
Troubleshooting Tips
If the tree does not illuminate, try stepping on the Function change foot pedal
and make certain the wall switch is turned on.
If one section of your tree does not illuminate, check that section for cut or damage
wires or that all electrical connections on tree are made.
Due to unique construction of the light sets, the individual LEDs are not replaceable.
The light sets are designed for continued operation even if an individual LED fails to light.
Tree Storage
1. Remove the tree's main extension cord plug from the wall outlet.
2. Starting at the top, disconnect the top and section B.
Step A: Gently fold the branches up
toward the center.
Care should be taken
to avoid damage to the lights.
3. Disconnect sections B and A.
4. Refer to the drawing on how to
repack your tree.
IMPORTANT: Store your carton neatly in a cool, dry location protected from
sunlight to prolong the tree life and to better keep the light sets in working order.
Do not place a heavy load on the carton to avoid damage to or crushing the carton
and tree inside.
SPARE PARTS: Your tree includes a plastic bag containing spare two (2) 3-amp
fuses as replacements for the plug.
7.5 FT
AC PLUG
FOR
TREE TOP
Function Change
Foot Pedal
OPEN
FOR INDOOR USE ONLY
FUNCTION LIST:
1: Steady ON
2: Full / Half-light change
3: SLO-GLO
4: Change
5: Off
7.5 FT TREES
A
B
TOP