ManoMano Z2 Manual De Instrucciones página 13

FITTING THE HANDLEBAR (Fig. 4)
n
(8) and nut (9) in the upper hole of the handlebar. Proceed in the same way for the lower hole (A), by fitting the other screw (7),spacer (13) and the
washers h.4 (12) in the knob (10) and knob (11), complete with nut, in the sequence shown in the illustration. For further details, see the handlebar
adjustment chapter.
HOW TO MOUNT THE ACCELERATOR WIRE (Fig. 5)
n
"A " in the figure. Move the throttle lever(2) on the handlebar to the end of its stroke as shown by arrow "B " in the figure. Insert wire (3) into hole (4),
secure the sheath (5) with retainer (6) and screw (7). ATTENTION: in the position "stop" the throttle lever must stop engine.
FITTING THE BELT TIGHTENER CONTROL CABLE (Fig. 6-7)
n
this must be connected to the control lever (2) fitted on the handlebar. FORWARD MOVEMENT fit the end (4) of wire (5) in the lower hole (3) of lever
(2). Pass the wire (5) complete with register (7) in the through hole of prong (6). In the case of motor hoes with REVERSE GEAR, fit the end (10) in
hole (11) of the reverse gear lever (1). Pass the wire (8) complete with register (9) in the through hole of prong (12). FOR MODEL Z3: terminal (4) has
to be inserted into the lever internal hole (2) as shown in the picture 7.
SETTING THE CONTROLS (Fig. 6)
n
be performed by adjusting the wire register. Furthermore, the lever that controls hoeing start (2) must only start the cutter after completing half its travel.
SETTING THE DREWBAR (Fig. 2)
n
(1) can be adjusted by loosening the handle (2) so as to keep the machine in horizontal working position. Once adjustment has been made, tighten
the handle (2).
SETTING THE HANDLEBAR (Fig. 4)
n
(7) in the holes that best suit your working requirements. For side-adjustable version only: the handlebars can be turned to the right or left by lifting
the lever shown in (Fig. 11 part 1). If the lever device (1) seems not to be working , please unscrew or screw up the nut (2) which is placed under rhe
handlebar support (Fig. 10).
INSTRUCTIONS
n ATTENTION ! Before switching the engine on, carefully check if the motor-hoe is in perfect good repair. IMPORTANT:
at the first use of the machine it is absolutely necessary to verify that inside the chassis to be present the lubrication oil. Do no start the
unit/machine on before having done such control. When you have finished the assembly, switch the motor hoe on and check , bringing
the accelerator to stop position , the engine to shut completely down.
- Engine instructions: Carefully read the istructions booklet anclosed to the relevant engine.
- Check if the air filter is clean.
- Fill the tank in as per the fuel described in the engine specifications and using a filter filling funnel.
- Do not change the calibration of the speeds control rotation device of the engine in order not to over-speed it.
- Starting the motor Open the fuel cock (for motors that feature such cock) and position the accelerator lever (Fig. 9 part 1) on the handlebar on
START. For cold starting, refer to the motor booklet. Grip the start handle and give a strong pull.
- Forward speed (fig. 6) : grip the handlebars and press the safety device (13) which is preventing the accidental tines connection. Pull the forward
Fasten the 2 handlebars (6) to support (1) by inserting the through screw (7) ,spacer (13), washers
Position the lever (1) on the engine at the end of its stroke as shown by arrow
Important! The cutter must only start turning after the relevant controls have been set. This setting can
To achieve correct hoeing and correct forward movement of the motor hoe, the height of the drewbar
The handlebars can be height-adjusted. Loosen the knobs (10) and (11) and fit the through screw
The control wire is already fitted to the belt tightener spring, but
UK
8