Cleaning & Maintenance - Hendi 7000 Manual Del Usuario

Type of cookware Cookware with a
bottom thickness
over 1.5 mm.
Note: Using a pan or pot that's not suitable for induction cook-
ing may damage the appliance.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
• No parts are dishwasher safe.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
Troubleshooting
Completely closed
If the appliance does not function properly, please check the
containers or cans.
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problem
The appliance does
not switch ON.
Cooling fan is
operating even
after the appliance
is switched to
Standby mode.
Error code identification
Error codes
E1
E2
E3
Warranty
Any defect affecting the functionality of the appliance which
becomes apparent within one year after purchase will be re-
paired by free repair or replacement provided the appliance has
been used and maintained in accordance with the instructions
and has not been abused or misused in any way. Your statutory
rights are not affected. If the appliance is claimed under war-
ranty, state where and when it was purchased and include proof
of purchase (e.g. receipt).
In line with our policy of continuous product development we
reserve the right to change the product, packaging and docu-
mentation specifications without notice.
Possible cause Possible solution
• Power plug is • Check the power
not connected
properly with the
electrical outlet.
• On/Standby (7) or • Press the On/
(10) button is not
pressed.
• This is normal. • Wait until the
The cooling fan
continues run-
ning in Standby
mode for some
time to cool
down all internal
elements.
Possible cause Possible solution
The temperature Clear all obstacles that
of the appliance is around the appliance.
too high Unplug the appliance,
remove the pan or pot,
wait until the appliance
is completely cool down.
Cooling fan defective Contact the supplier.
The pan or pot is Unplug the appliance,
overheated. remove the pan or pot,
Possibly, the pan wait until the appliance
becomes empty and is completely cool down.
appliance will shut And make sure water is
down for protection. inside the pan.
The supply voltage Make sure that the
is abnormal. (Supply appliance is connected
voltage is too high or to a suitable electrical
too low) power supply.
GB
plug to make
sure it is con-
nected properly.
Standby (7) or
(10) button to
start operation.
cooling fan stops
rotating.
9