Symbols; Operating Instruction; Cleaning And Maintenence - MaxPro PROFESSIONAL MPEM1250V Manual De Instrucciones

9.The workers must keep awake and be dedicated to workpieces and tools during work. They shall not use
any tool when they ar red.
10.Before use, tools shall be carefully inspected to confirm whether the tools are damages, whether the
damaged c affect normal performance, whether all movable parts are located a
and whether fixed parts are fastened, etc. If the tools are damaged, they shall be repaired or replaced at
special repair shops and shall not be used constrainedly.
11.In case of replacement of parts, original accessories must be used.
12.It shall be confirmed that the output sha
rod and the s rod is reliably connected with the s
13.This t htly and shall not be operated with single hand.
14.Prot ve glasses shall be worn to prevent eyes from injuries.
15.Hands shall not touch rotary components to prevent injuries.
16.Rota tools shall not get out of hand.
17.A er the opera st stopped, no liquid shall be exposed from the s
liquid may be splashed onto your clothes.

SYMBOLS

Read the manual
Warning

OPERATING INSTRUCTION

1.Installation
Note: the power plug must be unplugged from the power outlet before installation.
Install and replace the stir bar. (Figure 1)
Check the stir bar for deformation or damage before installation.
When the stir bar is inserted into the output shaft of the mixer, it should be inserted in place. The fixed nut
of the mixer should be tightened with the 22mm wrench provided to fix the stir bar firmly. (Figure 2)
Note: start with the low gear first, and gradually adjust to the desired speed.
When the stirring is damaged or other types of stir bars need to be replaced, first turn off the mixer,
pull the power plug out of the power socket, and then loosen the fixed nut of the stir shaft to remove
the stir bar. (Figure 2)
2. Operation
1) Before starting, you need to confirm the working voltage which must be the same as that on the
nameplate (220V).
2) Switch operation (Figure 3)
The mixer is equipped with self-locking keys to meet the needs of continuous work.
When the switch of the mixer is pressed, the machine will start working. When the switch is released, the
machine will stop working.
When the switch of the machine is pressed, it will start working and it will continue to work when press the
self-locking switchinto the machine.
4
x htly screwed into the thread of the s
ate, so as to prevent accidents.
ate, otherwise the
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Disconnect from power supply while
maintance
GB
When the machine is in continuous working state, press the switch of the machine, so that the
self-locking key will be reset and the continuous working state will end.
3) Speed control. (Figure 4)
This mixer is equipped with a governor.
When the machine is started, the speed can be increased or decreased by turning the governor.
It is recommended that the mixer be started at a low speed. After the machine starts working,
increase the speed through the governor to meet the actual working needs.
4) Operation requirement
The mixer needs to be operated by both hands when working. (Figure 5)
It is not allowed but accidents shall be avoided during operation. (Figure 6)
CLEANING AND MAINTENANCE
1.Before maint ower plug must be unplugged. Unfavorable a achments such
as dust and oil shall be frequently removed from tool surfaces to keep the tools clean.
2.The screws at c
from any crack or damage.
3.The power lines shall be frequently inspected for damages of insula
4.Worn drill bits will result in motor faults and reduce the efficiency, so drill bits shall be replaced or re-
sharpened when they are worn. When drill bits with worn or brok
to slipping, so new drill bits shall be used.
5.Motors are important parts among the tools, so they shall be frequently maintained to prevent ingress of
oil or water from damaging the motors.
6.A er opera for about 60h, carbon brushes shall be inspected. If necessary, a new pair of carbon
brushes can be used.
requently inspected for loosening. The shell shall be free
ps are used, they will cause risks due
GB 5