Safety Instruction For Table Saw - MaxPro PROFESSIONAL MPBTS1800/254 Manual De Instrucciones

f) Keep cu tools sharp and clean. Properly maintained cu
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these ins
account the working co s and the work to be performed. Use of the power tool for opera
different from those intended could result in a hazardous situa
5) SERVICE
a) Have your power tool serviced by a qualified repair person using only iden cal replacement parts. This
will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTION FOR TABLE SAW

Symbols Observe the dimensions of the saw blade. The hole diameter must match the tool
spindle without play.
Danger Area! Keep hands far away from the cu
Keep bystanders away.
1.When using the saw blades with hard metal teeth (Carbon
nega ve or slightly ve cu angle. Do not use any saw blades with deeply cut teeth. They can grip
the prot ve cap.
2. A en rst carefully assemble all the parts before st
3. If you are not familiar with using such a machine, you would be be er to be informed first by a
professional, an instructor or by a technician.
4. Always clamp or press the workpiece firmly against the saw guide, before you carry out the process. The
use of all possible clamping set-ups is preferable to using your hands.
5. Important: If you are holding the workpiece by hand for the process to be carried out, keep a minimum
distance of 100 mm from the saw blade.
6. Always press the workpiece against the bench.
7. Keep the saw blade sharp and check regularly whether it rotates freely without abnormal vibra
Replace the saw blade if necessary.
8. Allow the machine to rotate freely un it reaches the maximum number of rev
the process.
9. Maintain the air inlets at the back and the bo om of the bench saw machine and electric engine for a
longer machine life. Dust piles must be removed.
10. Always lock the different degree set-ups before you start processing.
11. Only buy suitable saw blades with a number of rev
12. Only use the correct saw blade. Too small or too big saw blades are extremely dangerous.
13. Regularly inspect the saw blade for any faults. Replace the saw blade if necessary.
14. Grease the new saw blade and clean the flanges before you assemble the new blade. Then assemble
the blade in the correct dir
15. Only use original flanges. All other types are not suitable.
16. Never work without the prot ve cap of the saw blade.
17. The moving part of the prot ve cap must also remain assembled.
18. Never grease the saw blade while it is rota
19. Always keep your hands removed from the track of the saw blades.
20. Never pick up the workpiece by grasping with your hands along or behind the saw blade.
21. Ensure that the workpiece never touches the saw blade before the machine has been switched on.
22. Never process metal or stone sorts with this machine.
4
tools with sharp cu edges are less
rea while the machine is running.
it is advisable to use blades with a
work. Follow the procedure as indicated.
before you start
at least 6000 rev
ges firmly using the central bolt.
GB
23. Use support aids in order to support long workpieces.
24. Never use the machine in a dangerous environment, where inflammable gases or fluids are present.
taking into 25. Never leave the machine una ended without first disc
s 26. If you hear abnormal noises, try to trace them or take the machine to a recognized fi er, or repair
company.
27. If a part is broken or damaged, replace it or repair it immediately.
28. Never stand in the track of the saw blade but stand to the le
29. Your hands must likewise be placed next to the track of the saw blade.
30. Always use a wooden pole instead of your hands to push the wood through the saw.
31. Always place the wood at the front of the saw bench and then push it further back.
32. For mitring only the adjustable guide must be used and the fence must be removed.
33. Never use the fence as a linear measure for cu
34. If the saw blade is blocked: first switch off the machine before you a end to the fault.
35. Avoid workpieces hi
1)Always use sharp saw blades.
2)Do not saw too small workpieces.
3)Never release the workpiece before it has been completely pushed through the saw.
4)Always adjust the guide parallel to the saw blade.
5)Never remove the saw prot
36. Before you con
37. Never use thinners to clean the machine. Only use a damp cloth for cleaning.
38. Do not use saw blades which are damaged or deformed.
39. Replace table insert when worn.
40. Use only saw blades recommended by the manufacturer.
41. Take care tha
42. Connect circular saws to a dust-c
43. Use and correct adjustment of the riving knife.
44. Use and correct adjustment of the upper saw blade quard. 45. Take care when slo
45. Take care when slo
Before use, remove the transport prot
1)Disassemble the bo om plate by loosening the 4 screws.
2)Remove the transport prot
3)The handles for height and mitre se
the machine.
.
4)Reassemble the bo om plate.
Replacing cables or plugs
Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to
insert the plug of a loose cable in the wall outlet.
Using extension cables
1)As a supply for this machine always use an unloaded line and/or an extension cable with conductors of
at least 1,5 mm² and protected with a 16 A fuse. Be sure that this extension cable is not longer than 20
te.
metres.
2)Only connect your machine and/or extension cable to an earthed electricity mains.
3)This machine can be switched to the single phase network (220-240V~ 50/60 Hz). If you are in doubt
about the earth of the electricity provisions, consult an electrician first.
ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS
Warning! The laser beam poten
beam.
During use, do not point the laser beam at people, directly or indirectly through re
This laser complies with class 2 according to EN 60825-1/A11, 1996. The unit includes no servicing
components. Do not open the housing for any reason. If the unit is damaged, have the damage repaired by
an authorized repair agent.
rom the mains voltage.
ff beams.
your dir by taking the following measures:
awing, ensure that you are standing firmly and that your hands are in the required
aw blade depends on the material to be cut.
evice when sawing.
ow motor.
of the saw blade are located in the transport prot
causes severe eye damage. Never look or stare directly into the laser
GB
ht of the saw bench.
inside
faces.
5