Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Product Overview
Read this manual carefully before using the product and follow the instructions and recommendations included herein. Refer to
wiki.2n.com for complete user documentation.
The 2N® IP Style is a 2N IP intercom of the very highest quality with a 10" touchscreen display, card reader, with support for Bluetooth
and NFC technologies as well as a Full HD camera with a function for facial monitoring during the call, so-called Face Zooming. The
2N® IP Style allows you to control the entrance area and perform remote access management. The intuitive touchscreen display
allows visitors to easily search the phone book and call the selected destination. 2N® IP Style is available in versions with a combined
and secured combined card reader with frequencies of 125 kHz and 13.56 MHz.
The touch display can be protected with hardened glass with active hygienic protection installed in the factory or the protection can
be additionally provided. A unique antibacterial/antivirus protection kills 99 % viruses and bacteria. The hardened glass with 9H
rating provides a sufficient display protection against scratching and, thanks to IK08 resistance, against breaking too.
Installation requirements
•
LAN connection, UTP cable Cat5 or higher with an RJ-45 connector
•
PoE+ 802.3at or 12 V DC / 4 A power supply
•
Completed installation of the chassis (order no. 9157002) for surface mounting, or a flush mount box (order no. 9157001) for
flush mounting.
Mechanical Installation
The device is designed for surface or flush mounting.
It is anticipated that installation of the chassis or the flush
mount box has been completed and all of the required cables
have been laid and are ready for connection. Recommended
length of prepared cables 30 cm.
Unscrew the connector cover on the back of the device. Thread
all of the cables with no connectors (terminals or end pieces,
etc.) through the bushing on the inside of the connector cover.
After threading the cables through the bushing, fit the required
end pieces.
Fold out the mounting bracket located at the bottom of the
chassis or flush mount box. The back of the device has profiles
which are fitted into the mounting bracket and slid down to the
Electrical Installation
Description of terminals, connectors and available components
CONTROL
POWERLED
LAN
VBUS
IN1, IN2, IN3
TAMPER SWITCH
OUT
RELAY
POWER 12 V / 4 A
LAN connector
Tamper Switch
SD CARD
Connection of a lock
Connect the electrical lock directly to the active output of the device. In any case, you are recommended to use low-consumption
locks and keep the limits mentioned above.
Installation security
If the device is installed in a location where there is a danger of unauthorized tampering with the device, we strongly recommend use of
a 2N® Security relay (order no. 9159010) to ensure the maximum security of the installation.
Factory Default Resetting – Follow the instructions below to reset the factory default values:
•
Disconnect the device from the power supply.
2
Button for restoring factory settings
Device status LED
LAN connection status LED
Connector for connection of a bus
Grounding terminal
Input terminals in passive / active mode (−30 V to +30 V DC)
•
OFF = open contact OR UIN > 1.5 V
•
ON = closed contact OR UIN < 1.5 V
Terminals for connection of the device to a security system
Active output 12 V / 0.6 A DC
Terminals for 30 V / 1 A AC/DC NO/NC contact
Terminals for external 12 V / 4 A DC power supply
Optionally PoE+ 802.3at for connection of the device to the LAN
Switch detecting unauthorized opening of the device
SD card slot
lowest possible position, anchoring the device by snapping it
into place.
Connect all of the cables to the device. The mounting bracket
provides sufficient support when connecting the cabling so it is
not necessary to support the device in any way.
After connection and securing of superfluous cabling in the
clips, screw the connector cover back on and fold in the device
towards the chassis or the flush mount box and then press in a
downwards direction to seal the installation. Then all you have
to do is lock the position by tightening the two screws inside the
device using an Allen key.
Graphical illustration of installation can be found at the end of
this short manual.
EN
Tabla de contenido
