Storing The Machine; Disposing Of The Machine - BM2 BIEMMEDUE BWK BAT Manual Del Usuario

8.1 Safety rules for routine maintenance
Routine maintenance involves a series of simple operations to be
performed at regular intervals and according to the manufacturer's
instructions. The Manufacturer has reduced the number and
complexity of routine maintenance operations to enable them to be
performed by personnel without technical expertise or complex
equipment. It involves above all:

Checking the water and fuel filters

Cleaning the connectors and greasing the connector gaskets
8.2 Safety regulations for cleaning the machine
All cleaning operations must be performed with the machine
stationary and turned off.
When cleaning the machine or its components, the following
precautions must be observed:
Do not clean electrical equipment with water or other fluids. To
remove dust, use a clean brush or dry cloth only. Do not clean
plastic surfaces with alcohol, detergent or solvents. Dispose of
cleaning materials in respect of current legislation. Do not
dispose of the materials used or cleaning residues in the
environment. To clean, use water or compressed air and soft
cloths. IMPORTANT - During cleaning, personnel protection
devices must be worn
8.3 Safety regulations for repairs and special
maintenance
For all operations over and above normal routine maintenance,
contact an authorised repair workshop.
All operations must be performed by qualified
personnel with the necessary technical skills to
perform the operations in the maximum safety and in
respect of current legislation.
It should be noted that the warranty offered by the manufacturer is
invalidated if:

The instructions given in the "use and maintenance" manual are
not scrupulously respected,

Routine maintenance is not performed as and when indicated;

Lubricants other than those specified are used;

Repairs or maintenance are performed by unqualified personnel;

Non-original spare parts are used;

Unsuitable tools are used.
IMPORTANT - The customer is responsible for
verifying that original parts only are used when
carrying out repairs. The use of non-original spare
parts could jeopardise the safety of the machine.
When ordering spare parts, specify the model of the machine,
registration number, reference number of the component in the
spare parts book and quantity.
9 Machine storage conditions

9.1 Storing the machine

If the machine is not used for long periods, protect exposed parts
(not protected by paint, surface treatment or plastic) with protective
rust prevention oils. If the machine is not to be used for particularly
long periods, you should also clean it thoroughly. After performing
these operations, seal the machine inside an opaque black
multilayer nylon bag together with a suitable drying agent (silica gel).
10 Disposal
10.1

Disposing of the machine

For countries in the European Union, before disposal, check the
technical data label on the machine: if the symbol shown on the side
is present, it means that the disposal is subject to the European
directive 2012/19/UE regarding Waste Electrical and Electronic
Equipment, WAEE, and to current national norms. Therefore, the
regulations and guidelines of the local system for the disposal of
electrical and electronic devices must be strictly followed.
11 Table of regular maintenance
OPERATION
Check the functioning of all
controls
Check connector gaskets
Check filters
12 Troubleshooting
The table below gives the most common problems which may arise
during normal use of the weed removal system. These problems are
easy to resolve with operations classified as routine maintenance If
the problem is not present in the following table or cannot be
eliminated following the instructions here, contact an authorised
service centre.
PROBLEM CAUSE
Machine does not Electrical power
start supply absent or
inadequate
Electrical
protection
tripped
Motor does not start Inadequate
but makes a noise voltage
Inadequate Nozzle blocked
pressure or damaged
Valve dirty or
worn
Vibrations and/or The pump is
abnormal water sucking in air
discharge
Air in the hoses
Pump gaskets
worn
Pump noisy Bearings worn
Water leaks Worn gaskets
The water does not No diesel
heat up or the
Dirty diesel filter
temperature is
insufficient
Thermostat not
working
Coil blocked
X
X
X
SOLUTION
Check the
characteristics of the
power supply line
Contact customer
service
Check the
characteristics of the
power line
Clean or replace
Contact customer
service
Check water supply
connectors
Vent the air by
disconnecting the
hose
Contact customer
service
Contact customer
service
Order replacement
gaskets from a
service centre
Fill up
Check and clean
Request a
replacement
Contact customer
service