Operating - VONROC EH518AC Traducción Del Manual Original

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 28
EN
6. Handle
7. Air inlet
8. Tip-over switch

3. OPERATING

Check the device for damage before use
and only use in good working condition.
When using the heater for the first time, you may
notice a slight emission of smoke. This is quite
normal and it stops after a short time. The heating
element is made of stainless steel and was coated
with protection oil by production. The smoke is
caused by the left oil when heated.
Placing the electric heater
• Place the heater upright on a firm and a level
surface.
• Keep a minimum distance of 1 m between the
front of the housing and walls and 30 cm from
all other housing surface areas. Keep away from
wet environments.
Warning! Make sure to place the heater in a
safe spot, so you cannot easily trip over the
machine and cable. Make sure to place the
heater where it cannot fall down/ of.
Starting the electric heater (Fig A, B)
• Plug in the cable to the mains power outlet.
• Turn the main switch (4) on.
• Press the on/off button (2A) to start the heater.
The last setting has been saved. Press the
mode button (2D) to change the heating mode.
- Fan: the mode indicator (3B) will show one
dot.
- Low heating mode – 1000W: the mode indica-
tor (3B) will show two dots.
- High heating mode – 2000W: the mode indica-
tor (3B) will show three dots.
Adjusting the temperature (Fig. B)
• By default, the ambient temperature is shown
on the display (3).
• The last setting has been saved. The temperatu-
re can be set between 16
• Set the temperature as desired by press the
temperature / timer increase or decrease but-
ton (2B, 2C).
• The target temperature will keep flashing for 5
6
• The display dims after one minute of inactivity.
Constant room temperature
The heater starts and stops automatically to keep
the room temperature constant. Once the ambient
temperature in the room reaches the desired target
temperature, the heating element will be in standby
mode. Once the ambient temperature starts to
decrease, the heating element will be switched on
again.
Set the timer
The timer can be set between 1 hour and 9 hours.
Hold on the mode button (2D) for 5 seconds. The
display (3) shows flashing the duration currently
set for 5 seconds. Press the temperature / timer
increase and decrease button (2B, 2C) to set the
timer with 1 hour intervals.
The display (3) alternately shows the set timer and
ambient temperature. Without a timer there is no
limit.
Tip-over switch (8)
This heater has an mechanical tip-over protection.
This protection ensures when the heater is not
placed upright on a firm and level surface or when
the heater tip over, the system will automatically
shut the heater off. If this occurs, put the heater on
a firm and level surface and start the heater again.
Automatic Overheat Safety Control
This heater is equipped with safety internal heat
limiting thermostat and overheat protection circuit.
When a potential overheat temperature is reached,
the system will automatically shut the heater off.
If this occurs, the heater can only resume after
resetting it. To reset the heater: Unplug the heater
and wait at least 30 minutes to cool down before
restarting the heater.
Stopping the electric heater (Fig. A)
C and 37
C.
• Press the on/off button (2A).
o
o
• The fan mode will start and will cool down the
• Turn the main switch (4) off.
• Pull the plug out of the mains power outlet.
seconds after the last button press, then the
display will show the ambient temperature.
Let the machine cool down before turning
off by using the ventilation function.
heater for a few minutes.
WWW.VONROC.COM
Tabla de contenido
loading

Tabla de contenido