Wolf Garten LT 25 eM Manual De Instrucciones página 21

Safety information
¾ Remove the operating arm from the device
when carrying the device to or from separate
working positions.
¾ Never bypass or manipulate safety devices
installed on the device.
¾ Do not push the line box into the ground
or hit it against wall edges. If the line box
suddenly receives a heavy blow, be prepared
for increased vibration at the handle. If this
does occur, the device must be checked and,
if necessary, repaired by a qualified expert or
workshop.
Information about vibrations
¾ Vibrations can cause nerve damage and
impair the blood circulation in the hands and
arms.
¾ When working in the cold, wear warm clothing
and keep your hands warm and dry.
¾ Take breaks.
¾ If you notice that the skin of your fingers
or hands goes numb, tingles, hurts or goes
white, stop working with the machine and, if
necessary, consult a doctor.
¾ The specified vibration emission values:
• Were measured according to a standardised
testing procedure.
• Make it possible to estimate the power tool
emissions and compare these with different
power tools. Dependent on the conditions of
use, the state of the power tool or tools inserted
for use with it, the actual vibration load may be
higher or lower. When estimating the emis-
sions, consider doing so during work pauses
and phases when the tool is under reduced
load. Based on the correspondingly adjusted
estimated values, take protective actions, e.g.
organisational actions.
After use
¾ Switch the device off, remove the operating
arm, in which the permanently installed power
pack is located, from the device and check
the device for damage. Attention, danger!
Cutting tool still running!
¾ If you need to clean or service the device,
switch it off and remove the operating arm,
in which the power pack is located, from the
device.
¾ Always wait until the cutting tool comes to
a standstill and do not touch any moving
dangerous parts without first removing the
operating arm, in which the permanently
installed power pack is located, from the
device.
Safety information
¾ Removal of safety devices or replacement of
the line spool must only be performed with
the operating arm removed, in which the
permanently installed power pack is located.
Use only original line spools and observe the
fitting instructions!
¾ Ensure that ventilation slots are free from dirt.
¾ Do not clean the trimmer using water.
¾ Store the device in a secure location.
¾ Store the device out of reach of children.
¾ Do not repair the device yourself; it must be
repaired by a qualified expert or workshop.
¾ Let the device cool down before putting it
away and/or storing it.
General safety information
¾ Never replace the non-metallic cutting
element with a metallic cutting element!
¾ Always wait until the cutting tool comes to
a standstill and do not touch any moving
dangerous parts without first removing the
operating arm, in which the permanently
installed power pack is located, from the
device.
¾ Spare parts must meet the requirements of
the manufacturer. Therefore, use only original
spare parts or those spare parts authorised by
the manufacturer. When replacing spare parts,
always observe the supplied fitting instructions.
Remove the operating arm, in which the power
pack is located, from the device beforehand.
¾ Repairs must only be performed by a qualified
technician or service centre. Specialist
workshop addresses can be found on our
website.
¾ Only use the power packs intended for this
purpose in power tools.
Use of other power packs can result in injuries
and fires.
¾ This trimmer is intended for the care of lawn
edges and smaller grass and lawn areas in
private households. The device must not be
used for purposes other than those intended
because of the risk of bodily injury to the user or
other persons.
¾ Only use the trimmer in daylight or under
bright artificial light. Keep your work area clean
and well lit.
¾ Only use the trimmer in dry weather
conditions. Keep the device away from rain or
dampness and do not use it during a storm. The
ingress of water into the trimmer increases the
risk of an electric shock.
EN
21