Roborock Q7 Manual Del Usuario página 7

1. Tidy cables and loose items from the
ground and move any unstable, fragile,
precious, or dangerous items to prevent
personal injury or property damage due
to items becoming tangled in, struck by, or
knocked over by the robot.
2. When using the robot in a raised area,
always use a secure physical barrier to
prevent accidental falls that may result in
personal injury or property damage.
Note: When using the robot for the first time, follow it
throughout its whole cleaning route and watch for potential
problems. The robot will be able to clean by itself in future
uses.
Place the dock
B1
Keep the dock on a level surface, flat against
a wall. Connect it to a power supply.
B1-1 More than 0.5m (1.6ft)
B1-2 More than 1.5m (4.9ft)
Notes:
• Allow more than 0.5 m (1.6 ft) of clearance on each side, and
1.5 m (4.9 ft) in front of the dock.
• If the power cable hangs vertical to the ground, it may
be caught by the robot, causing the dock to be moved or
disconnected.
• The dock indicator is on when the dock is powered on, and
off when the robot is charging.
• Keep the dock away from direct sunlight or anything that
may block the dock location beacon; otherwise, the robot
may fail to return to the dock.
• To ensure a better user experience of the mobile app, place
the dock in an area with good WiFi coverage.
Secure the dock
B2
Select a flat floor surface to place the dock
and wipe it with a dry cloth. Then, place the
dock on the selected surface against the
wall. Use the double-sided tape to secure
the dock better.
B2-1—Double-Sided Tape
Notes:
• Use of the double-sided tape to secure the charging dock is
optional.
• When necessary, remove the double-sided tape slowly to
reduce residue glue.
Secure the Moisture-Proof Mat
B3
After the dock is secured, use a dry cloth to
wipe the surface on which the moisture-proof
mat is to be placed. Tear off the double-sided
tape at the bottom of the moisture-proof mat,
and stick the mat on the floor.
Notes:
• Alway place the moisture-proof mat on wooden floors.
• The moisture-proof mat attaches better to smooth surfaces.
B4 Powering on & Charging
Press and hold the button to power
on the robot. Wait until the power light is
steady, and then place the robot on the
dock to charge. The robot is equipped with
high-performance lithium-ion rechargeable
battery pack. To maintain battery
performance, keep the robot charged
during normal use.
Note: The robot may not turn on when the battery is low. In
this case, place the robot directly onto the dock to charge.
07
Using the mopping module
B5
B5-1—Adjust the water flow
Slide the switch down to increase the water
flow and up to decrease the water flow.
B5-2—Fill the water tank
Remove the water tank stopper, fill it with
water, and close it.
B5-3—Install the mop cloth
Dampen the mop cloth and wring it until
it stops dripping. Insert it into the bottom
along the attachment slot and stick it firmly
in place.
B5-4—Install the mopping module
Slide the mopping module along the back
of the robot as indicated by the arrow. A
click indicates that it is locked in place.
Notes:
• To prevent excessive dirt buildup during first-time use, floors
should be vacuumed at least three times before mopping.
• If carpets are present, draw No-Go Zones or Invisible Wall to
prevent the robot going on them, or roll them up.
• To avoid water tank corrosion, do not use cleaning fluid or
disinfectant.
• The mop cloth should be cleaned after 60 minutes of
mopping to ensure water flow and cleaning performance.
Remove the mopping module
B6
When the robot returns to the dock after
cleaning, press the latches on both sides,
and slide the mopping module backwards
to remove it.
Notes:
• Wash the mop cloth after each use, and regularly empty the
water tank of unused water to prevent odor.
• Remove the mopping module when not mopping.