Tabla de contenido
Idiomas disponibles
Idiomas disponibles
5. PREPARE THE CABINET (
7. Measure the distance between both bottom bracket edges (F) (FIG. 10).
The table below shows the approriate distance needed.
N
ARROW EDGE
F From 19-3/8" to < 19-9/16"
F From 19-9/16" to 19-13/16"
F
If the measured distance needs to be shortened, screw two no. 8-32 x 1/4"
machine screws, in each bottom embossed cabinet brackets hole; this
will slightly bend the bottom part of the brackets (FIG. 11). Screw both
brackets until the appropriate distance is obtained.
Screws in bottom
embossed holes
F
H
ORIZONTAL EXHAUST INSTALLATION ONLY
This powerpack insert is factory shipped to exhaust vertically; however, it is
possible to make it exhaust horizontally (3¼" x 10" ducting only).
8. Cut the hole for the horizontal exhaust through the back wall of the cabinet
using the dimensions shown (FIG. 12).
CABINET
BACK WALL
5¼"
5¼"
3/4"
CABINET BOTTOM
NOTE: Since this manual covers different unit models, some details in
the following illustrations may slightly differ from your unit.
6. PREPARE THE UNIT
A
LL INSTALLATIONS
1. If present, remove all protective polyfilm from the unit and/or parts.
2. Remove the grease
filter by pushing down
on latch tab and tilting
the filter downward
(FIG. 13). Set aside
the filter.
3. D i s a s s e m b l e t h e
electrical compartment
cover (grey part in
FIG. 14) from inside
the unit by removing
its retaining screw.
Remove the parts bag
behind the cover. Set
aside the parts bag and
the cover along with its screw.
4. Punch out one of the
two knock-out holes.
Install anappropriate
7/8" diameter strain
relief (not included,
grey part in FIG. 15).
NOTE: The HCK44
cord connection kit
(optional) can be used
instead of the house
power cable. Refer to
the instruction packed
with the HCK44 cord connection kit.
H
ORIZONTAL EXHAUST INSTALLATION ONLY
5. R e m o v e
a n d
d i s c a r d t h e s c r e w
circled in FIG. 16.
NOTE: This screw
might be present or
not.
6. Unplug the blower cable
from its connector on
faceplate. Disassemble
the faceplate from the
unit by removing its
4 retaining screws (two
per side, circled in
FIG. 17). Set aside the
faceplate along with its
screws.
SCREWS
7. Remove the 4 screws
(two per side) retaining
the blower support plate
to the top of the unit
(FIG. 18). Carefully lift
out and set aside the
blower with its support
plate. The blower will
be reinstalled later in the
unit.
'
)
6. PREPARE THE UNIT (
CONT
D
H
ORIZONTAL EXHAUST INSTALLATION ONLY
W
IDE EDGE
8. From inside the unit,
detach the back plate
(grey part in FIG. 19)
by removing its both
retaining nuts using 3/8"
diameter socket. Set
aside the nuts and plate.
FIG. 10
9. Install the back plate on
top of the unit, where
the blower support plate
was. Orient the holes
n e a r b y t h e c o r n e r s
towards the back of the
unit. Assemble to the top
of the unit using 4 screws
previously removed in
step 7 (FIG. 20).
FIG. 11
V
ERTICAL EXHAUST INSTALLATION ONLY
10. F o r
r e c t a n g u l a r
ducting, use 2 included
no. 8-18 x 1/4" metal
screws to attach the
included 3¼" x 10"
adapter damper on top
of the unit, over the
blower exhaust opening
(FIG. 21).
NOTE: The damper hinge
must be towards the
front of the unit.
For round ducting,
u s e
4
3½"
n o . 8 - 1 8 x 1 / 4 "
metal screws to attach
t h e i n c l u d e d 6 - i n .
round (or 8-in. round,
FIG. 12
PM600SSV only) adapter damper on top of the unit, over the blower
exhaust opening (FIG. 21, 6-in. round shown).
NOTE: The damper hinge must be parallel to the sides of the unit.
7. INSTALL THE UNIT
1. Run house power cable
between service panel
and unit location. Stub out
a 2-foot length of power
cable inside the cabinet.
Insert the power cable
in the unit through the
7/8" diameter strain relief
previously installed.
NOTE: Not necessary if
FIG. 13
the optional HCK44 cord
connection kit is used.
SCREW
2. Insert the unit in the
cabinet, until you feel a
'click' from both sides
of the unit, confirming
that the Ease of Install
hooks rest on the top of
the cabinet bottom sides
FIG. 14
, or cabinet brackets
or
(FIG. 22). Move
the unit from left to right,
from rear to front and up
to ensure the Ease of
Install hooks are retaining
the unit inside the cabinet.
NOTE: The unit will be
protruding below the
cabinetry until tightened.
FIG. 15
NOTE: If, for any reason,
the unit has to be
removed from the
cabinet, it is possible
FIG. 16
to disengage the
E a s e o f I n s t a l l
hooks. To do so,
while holding and
pushing on one side of the unit, lift simultaneously Ease of Install
hooks levers (1 and 2, grey parts in FIG. 23) in the other side of the
unit until the hooks are retracted.
3. Lift the unit until contact is made
between the unit flange and
cabinet. Secure the unit to the
cabinet using 4 no. 8 x 5/8" wood
screws included in parts bag
(2 screws per side). Use upper
FIG. 17
or lower holes (1, 2, 3, 4, 5 or 6)
(FIG. 24).
!
WARNING
The Ease of Install hooks
TEMPORARILY
SCREWS
unit in place. The unit
MUST BE secured to the
cabinet using the included
4 screws.
FIG. 18
'
)
CONT
D
(
'
)
CONT
D
NUTS
HINGE
HINGE
i n c l u d e d
1
1 2
3
4
5
6
hold
the
!
WARNING
Never use this unit as a shelf.
7. INSTALL THE UNIT (
H
ORIZONTAL EXHAUST INSTALLATION ONLY
4. From inside the unit, slide the
3¼" x 10" adapter/damper in
the horizontal duct, then attach
it to the unit using aluminum
duct tape all around the joint
(FIG. 25). Ensure the damper
opens as shown in damper
side view.
FIG. 19
HOLES
5. Insert the blower with its support
plate inside the unit, where
the back plate was initially
(A). Attach to the unit using
2 nuts previously removed in
step 8 in PREPARE THE UNIT
FIG. 20
section (B) (FIG. 26).
6. R e i n s t a l l a n d s e c u r e t h e
faceplate to the unit using its
4 retaining screws (two per side,
circled in FIG. 27). Plug the
blower cable to its connector on
faceplate.
FIG. 21
8. CONNECT DUCTWORK
V
ERTICAL EXHAUST INSTALLATION ONLY
Ducted Installation
U s e 6 - i n . r o u n d , 8 - i n .
round (PM600SSV only)
or 3¼" x 10" metal duct to
connect the adapter damper
on the top of the unit to the
ductwork above (FIG. 28, 8-in.
round not shown). Seal the
joint using aluminum duct tape.
Non-Ducted Installation
A non-duct kit is required for this type of installation (purchase
separately, model number: HARKPM21).
To install, follow the instructions packed with the kit.
9. WIRING
!
Risk of electric shock. Electrical wiring must be done by
qualified personnel in accordance with all applicable codes
and standards. Before connecting wires, switch power off
at service panel and lock service disconnecting means to
prevent power from being switched on accidentally.
1. Using appropriate wire nuts (not
included), connect house power
cable to unit wiring: BLACK to
BLACK, WHITE to WHITE and
GREEN or bare wire to GREEN
ground screw (FIG. 29).
2. Reinstall the electrical cover in
the unit; ensuring the bottom
FIG. 22
tabs are inserted in their
embossed location. Secure in
place using its retaining screw
2
(FIG. 30).
CAUTION
FIG. 23
Take care not to pinch wires while reinstalling wiring cover.
10. INSTALL THE FILTER
Ducted Installation
Reinstall the grease filter.
Non-Ducted Installation
Attach the non-ducted filter (included with the HARKPM21 non-duct
kit) to the back of the grease filter using clips (provided with
1
non-ducted filter). To order a new non-ducted filter, use service part
2
3
number S99010464.
4
5
6
FIG. 24
'
)
CONT
D
DUCT
DAMPER
SIDE
VIEW
FIG. 25
A
B
FIG. 26
FIG. 27
FIG. 28
WARNING
WHITE
WIRE
BLACK
WIRE
HOUSE
POWER
GREEN
CABLE
GROUND
SCREW
FIG. 29
TABS
FIG. 30
Tabla de contenido
