Eye Hortilux LED 700-ES2i Manual De Instrucciones

Thank you for purchasing the LED 700-ES2i Ascend
LED Grow Light System . This rugged system utilizes a
®
robust thermal and electrical design with an extended
spectrum. This premium growth spectrum includes
ultraviolet and far-red energy, promoting stronger plant
growth and heavier flowers.
CONTENTS
1. EYE HORTILUX LED 700-ES2i Ascend LED Grow Light System
2. Power cord, 12 ft. (3.7 m)
3. (1) splitter and (2) RJ cables, 10 ft. (3 m)
READ AND FOLLOW ALL SAFETY INSTRUCTIONS BEFORE INSTALLATION.
• WARNING - RISK OF SHOCK - DISCONNECT POWER BEFORE INSTALLING or SERVICING SYSTEM.
• WARNING - Do not drape power cords over the system to avoid damage to cord.
• WARNING - To prevent eye damage avoid looking directly at the LEDs.
• CAUTION - RISK OF BURN: Driver box and LED boards may be hot. Do not touch system
when in operation or during cool-off period.
• The installation and use of the system is the responsibility of the end user. Incorrect use or
installation can lead to injury or death.
• Always adhere to the applicable electrical code, local rules and regulations when installing
or using the system.
• DO NOT open or disassemble the system, it contains no serviceable parts inside. Opening
the system and can cause electrical shock or electrocution.
• Use only with power cord supplied. DO NOT use the system when either its power cord or an
exposed wire is damaged. If cord of LED 700-ES2i is damaged, it should be replaced with an
original EYE HORTILUX power cord.
• Only connect the system to an electrical outlet or extension cord of appropriate type
and rating. Connect the system only to the power sources of the correct voltage using
the plug received.
• DO NOT modify power cords. Modifications to the power cords can lead to mechanical or
electrical failure including open or short circuits.
• Avoid coiled cords. Coiled cords may lead to electromagnetic interference.
• DO NOT pull the power cord to unplug the system, pull the plug only.
• DO NOT lift the system by any power cords.
• DO NOT hang system by power cord.
• DO NOT use the system near flammable, explosive or reactive substances.
• DO NOT spray or use chemical solvents around the fixture. The use of chemicals could
damage the fixture and would void the warranty.
• Allow 30 minute cool down before handling the system.
• Make sure system is properly supported with supporting chains and/or hooks.
• DO NOT mount system directly touching any surface (maintain at least 3" from the
top of the system to mounting surface).
• DO NOT submerge system in water. System is suitable for wet location use and is IP65 rated.
System is splash proof, but not waterproof. In the event the system becomes submerged,
first disengage the circuit breaker, then unplug the system before removing it from water.
System is not suitable for outdoor locations.
• DO NOT operate in ambient temperatures above 95°F/35°C. Note: Maintain the
temperature within the growing space below 86°F/30°C, otherwise ventilation/cooling
system may be required.
• It is possible to run multiple LED 700-ES2i systems on one circuit. To determine the
maximum number of systems a circuit can run, consult a licensed electrician and review the
current and voltage specifications in this document. Ensure the total circuit load does not
exceed the circuit rating.
Visit eyehortilux.com for the latest installation instructions.
LED 700-ES2i
®
SYSTEM INSTALLATION INSTRUCTIONS
NOTE: Inspect system for defects prior to installation. If defects are noticed do
not install and contact the manufacturer immediately.
1. Remove LED 700-ES2i from packaging.
2. Inspect for damage. If damage is noted, do not attempt to install
or operate.
3. This LED 700-ES2i is intended to be hung using the attached four (4)
corner hanging tabs. (Figure 1) Use mounting hardware suitable for the
surface involved, attach chain. Hardware and chain are to be capable of
supporting 100 lbs.
4. Hang LED 700-ES2i no closer than 18 inches above the plant canopy
for optimal growing. (Figure 2) Hanging height of less than 6 inches
is not recommended as plant growth and light uniformity will suffer.
If hanging more than one system, ensure the edge-to-edge distance
between systems is greater than 4 inches. Optimal spacing is 6 inches.
5. Plug female end of the input power cord into the system. To do so,
rotate cord end to match key alignment of the socket. Push cord end
in firmly until it clicks. (Figure 3) To release cord, push down on metal
clip and gently pull from socket.
6. Plug male end of the input power cord into the electrical outlet. If
using a hardwire cord, consult a qualified electrician for correct supply
termination. Use a suitably rated NEMA connector or hardwire (Black to
Line, White to Neutral, Green to Ground)
7. The LED 700-ES2i is now ready for operation.
The LED 700-ES2i will only turn on or off out of the box. You must use a
controller or external control system in order to dim by connecting the
driver to the controller with the included RJ cables. Follow controller
instructions for proper installation.
Hanging Tab
(Figure 1)
(Figure 3)
Mounting Height: 18 inches from canopy
18"
4'
4'
(Figure 2)
www.eyehortilux.com
EQS4703