Hama PREMIUM M10 Instrucciones De Uso página 5

2.3 Explanation of symbols used on the product label
Warning - risk of injury
Note the warning symbols in order to avoid injuries or damage to the device.
General warning symbol
Before commissioning, read the enclosed operating
instructions.
You must comply with the safety instructions at all times.
• This device is not intended for use by children.
• Avoid touching the intake opening with hands, clothing
or hair.
• Unplug the device if it is not going to be used for a
prolonged period.
Children must be supervised when using the device.
Do not insert paper clips into the intake shaft.
Do not reach into the intake shaft.
Keep clothing away from the intake shaft.
Keep jewellery, e.g. necklaces, away from the intake shaft.
Keep hair away from the intake shaft.
Do not use any aerosol products on or near the device.
Insert no more than 10 sheets of paper at any one time into
the intake shaft (see 7. Technical Data).
Do not insert CDs/DVDs into the intake shaft.
Intake shaft for credit cards. Only insert one credit card at a
time into the intake shaft for credit cards.
2.4 Safety device
The device is equipped with a safety switch and can only be operated if the basket (5) is
correctly inserted into the device.
Warning
Any tampering with or modi cation of the safety features can result in serious injury
and is not permitted.
3. Installation / Setup
Warning
• Only operate the product from a socket that has been approved for the device. The
socket must be installed close to the product and must be easily accessible.
Warning
• Disconnect the product from the power supply using the On/Off switch – if this is not
available, unplug the power cord from the socket.
• If using a multi-socket power strip, make sure that the total power consumption of
all connected devices does not exceed the socket strip's maximum throughput rating.
• If you will not be using the product for a prolonged period, disconnect it from
mains power.
Note
• Set the product up on a level, horizontal and su ciently stable surface.
• Route all cables so there is no risk of tripping.
• Do not bend or crush the cable.
• Protect the connecting cable from hot surfaces and sharp edges.
• Connect the power pack to a properly installed and easily accessible mains socket.
4. Operation
Note
• Be aware that the thickness of paper increases when it is folded, leading to the
device's maximum page capacity being exceeded.
• Always wait until one cutting operation is nished before starting the next one.
• Do not use the device continuously for more than 15 minutes at a time.
• Empty the container regularly in order avoid damaging the device.
4.1 Switching the device on
• Press the " " button (9) to switch the device on.
• The status LED "Ready" on the " " button (9) lights up solid blue.
• The device is now ready for use.
4.2 Switching the device off
• Press the " " button (9) to switch the device off.
• The status LED "Ready" on the " " button (9) goes out.
Note
If too much paper is fed in at the same time, the shredder stops automatically and ejects
the paper backwards. The status LED "Overload" on the " " button (9) starts to ash
red. This may have been caused by too much paper being stapled, paper that is too
thick, folded or not stacked neatly. Remove the excess paper and reduce the number of
sheets if necessary.
4.3 Shredding paper
• Insert the paper into the centre of the intake shaft (1). The cutting rollers switch on
automatically.
• Let go of the paper. Once the cutting process is complete, the device switches itself
off again.
4.4 Shredding plastic cards
• Insert the plastic card into the centre of the intake shaft (1). The cutting rollers switch
on automatically.
• Let go of the plastic card. Once the cutting process is complete, the device switches
itself off again.
4.5 Forwards / backwards modes
Note
These modes are designed to release any blockages of the cutting mechanism.
If a paper jam is detected in the intake shaft, the shredder stops automatically and ejects
the paper backwards (1). The status LED "Overload" on the " " button (9) starts to ash
red. If the paper then does not come loose, carry out the following steps.
• Press and hold the "REV" button (8). The rollers of the cutting unit now rotate in the
opposite direction and discharge the paper backwards.
• Remove the blocked cut material carefully from the intake shaft (1).
• The status LED "Ready" on the " " button (9) lights up solid blue.
• Ensure that the amount of paper does not exceed the maximum capacity.
• Once the paper jam is cleared, press the "FWD" button (10) to continue the shredding
process.
3