Tabla de contenido
Idiomas disponibles
Idiomas disponibles
TABLE OF CONTENTS
Limited warranty . . . . . . . . . . . . . . . . . . . . . . . 1
General safety instructions . . . . . . . . . . . . . . 1
Positioning of tile saw . . . . . . . . . . . . . . . . . . 1
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
California Proposition 65 . . . . . . . . . . . . . . . . 2
Electrical requirements . . . . . . . . . . . . . . . . . 2
Extension cords. . . . . . . . . . . . . . . . . . . . . . . . 2
Specific safety instructions. . . . . . . . . . . . . . 3
Saw features . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 3
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
A. Stand setup. . . . . . . . . . . . . . . . . . . . . . . 3
B. Motor assembly installation. . . . . . . . . 4
C. Installing upper frame wheels . . . . . . 4
hanger/tool caddy . . . . . . . . . . . . . . . . . 4
E. Diamond blade installation . . . . . . . . . . 4
F. Water pump installation. . . . . . . . . . . . . 4
tray installation. . . . . . . . . . . . . . . . . . . . 4
H. Extension table installations . . . . . . . . 5
Adjustable cutting table extension . . . . . 5
Cutting tile and stone . . . . . . . . . . . . . . . . . 5
Checking blade alignment. . . . . . . . . . . . . 5
Blade alignment instructions . . . . . . . . . . 5
Straight cuts . . . . . . . . . . . . . . . . . . . . . . . . 6
Diagonal cuts . . . . . . . . . . . . . . . . . . . . . . . 6
Plunge cuts . . . . . . . . . . . . . . . . . . . . . . . . . 6
Bevel/miter cuts . . . . . . . . . . . . . . . . . . . . . 6
Moving the saw . . . . . . . . . . . . . . . . . . . . . 6
Cleaning the saw . . . . . . . . . . . . . . . . . . . . 6
Water pump maintenance . . . . . . . . . . . . 7
Diamond blades . . . . . . . . . . . . . . . . . . . . . 7
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . 7
Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Exploded parts diagram . . . . . . . . . . . . . . . . . 9
LIMITED WARRANTY
Refer to warranty card.
GENERAL SAFETY
INSTRUCTIONS
READ THIS OWNER'S
MANUAL COMPLETELY AND MAkE
SURE YOU UNDERSTAND ALL OF IT'S
SAFETY GUIDELINES.
All manuals and user guides at all-guides.com
1. KEEP GUARDS IN PLACE and in
working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Always check to see that keys
and adjusting wrenches are removed from
tool before turning it on.
3. KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents.
4. DO NOT USE IN DANGEROUS ENVIRON-
MENT. Do not use power tools in damp or
wet locations, or expose them to rain. Keep
work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should
keep a safe distance from the work area.
6. MAKE WORKSHOP CHILD PROOF with
padlocks, master switches or by removing
starter keys.
7. DO NOT FORCE TOOL. It will do the job
better and be safer at the rate for which it
was designed.
8. USE THE RIGHT TOOL. Do not force tool
or attachment to do a job for which it was
not designed.
9. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Non-slip footwear
is recommended. Wear protective hair
covering to contain long hair.
10. ALWAYS USE SAFETY GLASSES. Also
use face or dust mask if cutting operation
is dusty. Everyday eyeglasses only have
impact resistant lenses, they are NOT
safety glasses.
11. SECURE WORK. Use clamps or a vise
to hold work when practical. This safety
precaution allows for proper tool operation
freeing both hands to operate tool.
12. DO NOT OVERREACH. Keep proper
footing and balance at all times.
13. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for lubri-
cating and changing accessories.
14. DISCONNECT TOOLS FROM OUTLET
before servicing; when changing accesso-
ries, such as blades, bits, cutters, etc.
15. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in the "off"
position before plugging in.
16. USE RECOMMENDED ACCESSORIES.
Consult the owner's manual for recom-
mended accessories. The use of improper
accessories may increase risk of injury.
17. NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.
- 1 -
Professional
10 in. Wet Tile Saw
18. CHECK DAMAGED PARTS. Before further
use of the tool, a guard or other part that
is damaged should be carefully checked
to determine that it will operate properly
and perform its intended function - check
for alignment of moving parts, binding of
moving parts, breakage of parts, mounting,
and any other conditions that may affect
its operation. A guard or other parts that
are damaged should be properly repaired
or replaced.
19. DIRECTION OF FEED. Feed work into a
blade against the direction of rotation of the
blade only.
20. NEVER LEAVE THE TOOL RUNNING
UNATTENDED. TURN POWER OFF. Do not
leave tool until it comes to a complete stop.
21. ALWAYS TURN OFF THE POWER while
adjusting the angle for miter cuts.
22. CUTTING TAbLE MUST bE IN THE
STARTING POSITION before adjusting the
cutting head, to perform bevel cuts.
23. ENSURE THAT THERE IS A CONTINUOUS
FLOW OF WATER to both sides of the blade
during operation.
24. CHECK DIAMOND bLADES CAREFULLY
FOR CRACKS, NICKS, MISSING DIAMOND
MATRIX OR OUT OF ALIGNMENT
CONDITION. Replace damaged blades
immediately. Do not use damaged blades,
which can cause bodily injury.
POSITIONING
OF TILE SAW
A. To avoid the possibility of the appliance
plug or receptacle getting wet, position
the tile saw to one side of a wall-mounted
receptacle to prevent water from dripping
onto the receptacle or plug. The user should
arrange a "drip loop" is that part of the
cord below the level of the receptacle, or
connector if an extension cord is used, to
prevent water traveling along the cord and
coming in contact with the receptacle (see
FIGURE 1).
B. If the plug or receptacle does get wet, DO
NOT unplug the cord. Disconnect the fuse
or circuit breaker that supplies power to the
tool. Then, unplug and examine for presence
of water in the receptacle.
709-3930
Tabla de contenido
