NuWave INFINITY 28202 Manual Del Propietário página 11

TROUBLESHOOTING GUIDE
The Infinity Blender becoming clogged and not operating
™
efficiently.
1. Certain ingredients can cause clogging. When using the Plunger Lid,
remove the Plunger Cap from the Lid and insert the Plunger through
hole. Press the ingredients down and around until mixture loosens
around the bottom of the Jar.
2. The ingredient amounts higher than specified are being used. Do
not fill the Jar above ¾ capacity (1.5 liters, 51 fl oz).
3. Large pieces of ice are not mixing properly. Use smaller pieces of ice.
The blended mixture has lumps or the texture is not even.
Air pocket has formed (cavitation) and mixture is too cold or has
solidified in areas, and the blades are spinning in cavity. Increase the
temperature by reducing ice in the recipe.
Noises or motions unusual for the normal operation of the Infinity
Blender are detected.
1. The Blade assembly may be loose, missing a part, or possibly
damaged. Turn the Infinity Blender OFF and unplug immediately.
™
DO NOT disassemble the Blade assembly. Call Customer Service:
1-877-689-2838 or email [email protected].
2. Foreign objects from ingredients may have been put into the Jar and
are making unusual sounds. Prior to adding your ingredients to the
Jar and blending, clean fruits/other ingredients and remove all debris
or any objects.
Error Message: Solution(s)
The NTC Temperature Sensor has short circuted.
Contact NuWave Customer Service 1-877-689-2838
Er1
or [email protected].
The NTC Temperature Sensor is open. Contact
Er2
NuWave Customer Service 1-877-689-2838
or [email protected].
The NTC Sensor has overheated. Turn the Infini-
ty Blender off and allow it to cool. If the Infinity
™
Er3
Blender is not working after it cools down, Contact
NuWave Customer Service 1-877-689-2838 or
[email protected].
20
troubleshooting guide
™
™
LIMITED WARRANTY
The NuWave Infinity High-Performance Blender
® ™
THE MANUFACTURER WARRANTS
The NuWave Infinity High-Performance Blender is warranted to
® ™
be free from manufacturer defects. This Warranty covers original
owner of this Blender for personal household use only. This Warranty
does not apply to products used for commercial, rental or resale
purposes. The Infinity Blades, Bearings, Motor Blender Base,
Blender Jar, Lid and Plunger are warranted for the lifetime of the
unit under normal household use, and when operated in accordance
with the Manufacturer's written instructions. The NuWave
High-Performance Blender is warranted for household use only and
not intended for commercial use. The Manufacturer will provide the
necessary parts and labor to repair any part of the NuWave
High-Performance Blender at NuWave, LLC Service Department.
Should the warranty be voided for any reason, the cost of the labor
and parts will be the responsibility of the owner.
Customer must register their NuWave
Blender within six (6) months of purchase date to be eligible for
warranty coverage. Customer can register by scanning the QR
code on the back of the unit, or by visiting www.nuwavenow.com/qr.
If customer fails to register their unit within 6 months of purchase,
the warranty will be voided.
THE WARRANTY DOES NOT COVER
The Limited Warranty is voided if repairs are made by an
unauthorized dealer and/or the serial number data plate is removed
and/or defaced. Normal fading or discoloration of the product
caused by exposure to sunlight or chemicals such as ammonia,
laundry detergent, or household bleach is not covered by this
Warranty. This Limited Warranty does not cover failure, damages
or inadequate performance due to accident, acts of God (such as
lightning), fluctuations in electric power, alterations, abuse, misuse,
misapplications, corrosive-type atmospheres, failure to operate in
Infinity
® ™
Infinity
® ™
Infinity High-Performance
® ™
21
nuwavenow.com