Quick DP3 Serie Manual Del Usuario página 17

POS. DESCRIPTION
1 Bent anchor winch lever
2 O-ring
3 Drum bush DP3 chromed
4 Drum 1000W
5 Gypsy cover
6 Top clutch cone
7A Gypsy 8 mm
7B Gypsy 10 mm
8 Bottom clutch cone
9 Screw M 6*55 stainless steel
10 Spring washer
11 Oil seal
12 Internal circlip
13 External circlip
14 Bearing
15 Short shaft
16 Oil seal
17 Key
18 Long shaft
19 Chain guide cover stainless steel -
20 Screw 3,9*25 stainless steel
21 Screw M5*50 stainless steel
22 Mooring rope puller DP3
23 Spring for pressure lever
24 Pressure lever
25 Cylindrical stainless steel pin 5*40 MBSC05040A00
26 Screw M4*26 stainless steel
27 Screw M5*40 stainless steel
28 Screw M4*25 stainless steel
29 Screw M4*40 stainless steel
30 Plastic chain pipe series DP3
31 Screw M8*20 stainless steel
32 Cover Base DP3 stainless steel
33 Plastic cover insert DP3
34 Aluminium round base DP3
35 Nut M 4 stainless steel
36 Nut M 5 stainless steel
37 Nut M 6 stainless steel
38 Gasket/ DP3 - shaped jig
39 Sensor
40 Stud 8*080 Ø8 stainless steel
41 Gearbox flange gasket TOP TG50 PGFLRDTG5000
42 Gearbox flange gasket TOP TG60 PGFLRDTG6000
43 Gearbox - Quick TG50 1000W
44 Washer
45 Grower
46 Nut
47 Washer
48 Self locking nut
49 O-ring
50 Gearbox - Quick TG70 1500W
DP3 700/1000/1500W - REV002C
CODE 51
52A
ZSLMSHR10000
52B
PGR031250000
52C
SGMSD1000R03
52D
ZSPMSE1000R3
52E
ZSPMSGB10R03
52F
MSF1000000R2
53A
ZSBDP3085160
ZSBDP3103800
53B
MSF10ATCN0R2
54
MBV0655MXCE0
55
MBR254025X00
56
PGPRL2547700
57
MBAN4717Y000
58
MBAE2520Y000
59
MBJ60052RS10
MSASDP300R00
PGPRL2540700
MBH080780F00
MSASDP3D0R00
MBV03925AXCC
MBV0550MXCEB
PDNCPDP30000
Quick
MMTND10ATC00
to marine environments. In any case, any salt deposits on the
PDLVTDDP3N00
outside must be removed periodically to avoid corrosion and
damage to the equipment. The parts where salt may have built
MBV0420MXCEB
up should be washed thoroughly with fresh water.
MBV0540MXCE0
MBV0425MXCE0
Once a year, the drum and the gypsy are to be taken apart as
MBV0440MXVEP
follows:
PDPS0DP30R01
MBV0820MXTSC
DRUM VERSION
MSGB0DP3X000
Use the handle (1) to loosen the bush (3); pull off the drum (4)
PDNC0DP30000
and the top clutch cone (6); loosen the fixing screws (9) of the
SGMSC0DP3A00
rope/chain stripper and remove it. Pull off the gypsy (7).
MBD04MXEN000
MBD05MXEN000
NO-DRUM VERSION
MBD06MHEN000
Use the handle (1) to remove the gypsy cover (5); remove the
PGBSDP300000
top clutch cone (6); loosen the fixing screws (9) of the rope/
SAKREED00000
chain stripper and remove it and pull off the gypsy (7).
MBP080808X00
Clean all the parts removed to avoid corrosion, and grease the
shaft thread (15 or 18) and the gypsy (7) where the clutch cones
SLMR10TG5000
(6 and 8) rest (use grease suitable for marine environment).
MBR08X000000
MBR08XDE0000
Remove any oxide deposits from the terminals of the electric
MBD08MXEN000
motor and the contactor unit; grease them.
MBR061815X00
MBD06MXET000
PGR023000000
SLMR15TG7000
MAINTENANCE
Key 5x5x15
Electric motor 700W 12V
Electric motor 700W 24V
Electric motor 1000W 12V
Electric motor 1000W 24V
Electric motor 1500W 12V
Electric motor 1500W 24V
Motor protection case 700W
Motor protection case
1000/1400W
Grommet
Terminal board cover
Screw
Bottom gasket
Bottom protec cover
Cable outlet
WARNING: make sure the electrical power to the motor
is switched off when working manually on the windlass.
Carefully remove the chain or rope from the gypsy or the
rope from the drum.
® windlasses are manufactured with materials resistant
GB
MBH050515F00
EMF071200000
EMF072400000
EMF101200000
EMF102400000
EMF151200000
EMF152400000
PCCCPM070000
PCCCPM100000
PCGPMMR00000
PCCPPMMR0000
MBV02213AXSC
PGGPMFN00000
PCCPPMFN0000
PPM20B000000
17