Before Use; During Use - stayer VENTO L20 Manual De Instrucciones

This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates of
our machines on the website: www.grupostayer.com
SPECIFIC SAFETY INSTRUCUIONS
1.

BEFORE USE

- Be familiar with the controls and the proper use of the
tool.
- Check the functioning of the tool befo re each use
and, in case of a defect, have it repaired immediately
by a qualified person; never open the tool yourself.
- Before use, thoroughly inspect the area where the tool
is to be used and remove all solid objects that could
damage the shredding mechanism when vacuuming
(such as stones, broken glass, pieces of metal).
- When vacuuming, never use the tool without the
collection bag in place.
- Regularly check the collection bag for wear or
damage.
- Replace worn of damaged parts
- Keep all nuts, bolts and screws tight to be sure that
the tool is in a safe working condition

DURING USE

- Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool.
- Operate the tool at a walking pace only {do not run).
- Keep proper faoting on slopes.
- Always ensure that the ventilation openings are kept
clear of debris.
- Take a secure stance when working (do not
overreach, especially when usi ng steps or a ladder)
EXPLANATION OF SYMBOLS ON TOOL
Read the instruction manual befare use.
Wear protective glasses.
Do not expose tool to rain.
Pay attention to the risk of injury caused by flying debris
(keep bystanders a safe distance away from work area).
Sw itch off and disconnect plug befar e cleaning/
maintenance or if (extension) cord is damaged or
entangled.
Double insulation (no earth wire required).
Batteries use and care
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against continuous
intense sunlight, fire, water, and moisture. Danger of
explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery
against dangerous overload.
ENGLISH
16
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The battery
can be damaged.
The battery is equipped with a temperature control
which allows charging only within a temperature range
of between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot
be subject to overload. When the load is too high or
the allowable battery temperature range of 0–50 °C
is exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction ,
until the tool can be inserted. Insert the tool. Firmly tighten
the collar of the keyless chuck 2 by hand in rotation
direction . This automatically locks the drill chuck.
The locking is released again to remove the tool when the
collar is turned in the opposite direction.
INSTRUCTIONS FOR USE
2.
Placement Tool
This tool has been designad far blowing/collecting as well
as vacuuming/shredding dry leaves and other dry garden
rubbish such as grass and twigs.
This tool is intended far domestic use only and is not
designad to be used under wet conditions.
This tool is not intended far professional use.
Read this instruction manual carefully before use and
save it for future reference.
Pay special attention to the safety instructions and
warnings; failure to follow these may result in serious
injury.
Check whether the packaging contains all parts as
illustrated in drawing
When parts are missing or damaged, please contact your
dealer.
16