Dust/Chip Extraction - stayer MULTI L20 Manual De Instrucciones

PRODUCT FEATURES
The numbering of the product features refers to the
illustration of the machine on the graphics page.
MULTI TOOL 300 PRO
1 On/Off switch
2
Thumbwheel for orbit frequency preselection
3
Venting slots
4 Tool holder
5 Handle (insulated gripping surface)
6 Cutting or sanding tool.
7 Clamping bolt with spring washer
8 Allen key
9 Sanding plate
10 Sanding sheet
11 Dust extraction device
12 Suction nozzle.
13 Lever useful change
MULTI L20
1 On/Off switch.
2
Thumbwheel for orbit frequency preselection.
3
Venting slots.
4 Tool holder.
5 Handle (insulated gripping surface).
6 Plunge saw blade.
7 Clamping bolt with spring washer.
3. ASSEMBLY
CHANGING THE TOOL
Before any work on the machine itself, pull the mains
plug.
Wear protective gloves when changing application tools/
accessories. Contact with the application tool/accessoriy
can lead to injuries.
ACCESSORY
HSS wood segment
saw blade
BIM segment saw
HSS plunge cut saw
blades, wood
BIM plunge cut saw
blades, metal
BIM plunge cut saw
blade, wood and
Base plate for
sanding, series Delta
MOUNTING/REPLACING THE APPLICATION TOOL/
ACCESSORY
180 Turn the lever to extract useful and change it. Return
around to fix the tool.
MATERIAL
Wooden materials,
plastic
Wooden materials,
blade plastic
Wood, metal non-
ferrous metals
Metal (e.g.
unhardened nails,
screws, smaller
profiles), non- ferrous
metals
Legno, metallo,
metalli non ferrosi
metal
Depends on sanding
sheet
93 mm.
Check the tight seating of the application tool/
accessory.
Incorrect or not securely fastened application tools/
accessories can come loose during operation and pose
a hazard.
Mounting/Replacing a Sanding Sheet on the Sanding
Plate
The sanding plate is fitted with Velcro backing for
quick and easy fastening of sanding sheets with Velcro
adhesion.
Before attaching the sanding sheet, free the Velcro
backing of the sanding plate from any debris by tapping
against it in order to enable optimum adhesion. Position
the sanding sheet flush alongside one edge of the
sanding plate, then lay the sanding sheet onto the
sanding plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes
in the sanding plate.
To remove the sanding sheet, grasp it at one of the tips
and pull it off from the sanding plate.
Selecting the Sanding Sheet
Depending on the material to be worked and the required
rate of material removal, different sanding sheets are
available:
- All wooden materials (e.g., hardwood,
softwood, chipboard, building board) .
- Metal materials
APPLICATION
For coarse-sanding,
e.g. of rough,
unplaned beams and
boards
For face sanding
and planing small
irregularities
For finish and fine
sanding of wood

DUST/CHIP EXTRACTION

Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful
to one's health. Touching or breathing-in the dusts
can cause allergic reactions and/or lead to respiratory
infections of the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-
treatment additives (chromate, wood preservative).
Materials containing asbestos may only be worked by
specialists.
- As far as possible, use a dust extraction system
suitable for the material.
- Provide for good ventilation of the working place.
- It is recommended to wear a P2 filterclass respirator.
Observe the relevant regulations in your country for the
materials to be worked.
CONNECTING THE DUST EXTRACTION (SEE FIGURE A)
For sanding, always connect dust extraction. Remove
the application tool/accessory when mounting the dust
extraction 11 (accessory).
- 21 -
GRAIN
Coarse 60
Medium 120
Fine 210
es
it
gb
fr
p
cz
el