Riding Operation; Getting Ready - ESKUTE ES MAX Manual Del Usuario

4 . Non-Pneumatic Tires
1. Inflation-free, maintenance-free, explosion-proof, anti-tie.
2. The wheel hub is fitted with the inner tube tire tightly, and the steel wire protection is more safe.
3. Excellent flexibility. The foamed inner tube adopts microwave closed-cell foaming to make the
performance of comfortability close to the traditional inflation tire.
4. Foamed inner tube adopts improved rubber and improved polymer environmental protection
materials, and the products are environmentally friendly and non-toxic.
5. Wear-resistant and anti-skidding. The shell uses a traditional rubber tire which has good
performance, and passed the market testing.
6. Weather resistance. It features with high temperature resistance, low temperature resistance and
aging resistance.
5. CHARGING
Charge the Eskute ES MAX before using it.
The charge cycle is complete when the battery indicator on display is full. Each charge cycle from zero
to full charge will take approximately 5 hrs. When the backlit display on the handlebars indicates that
battery power is low, recharge the ES MAX. To recharge the ES MAX, use the included charger.
Step 1. Make sure the scooter is powered off then locate the charging port under the deck.
Step 2. Insert the appropriate end into the charging port and then insert the other end into an outlet.
Step 3. While the scooter is charging, the charger light will turn red.
Step 4. When the scooter is fully recharged, the charger light will turn green. You may then disconnect
the scooter from the charger.
DO NOT(under any circumstances)use the scooter while it is charging or connected to the charger.
The charging time is approximately 5 hours. Charging longer than that may affect battery life and
performance. If the charger's light doesn't turn on, it may not be fully connected. Check that it is
securely attached to the socket port and to the scooter.

6. RIDING OPERATION

We sincerely hope every operator can ride the ESKUTE ES MAX safely. Note the following information
before attempting to ride your ESKUTE ES MAX.
● An ASTM F1492 approved helmet as well as other protective gear must be worn at all times.
● The ES MAX supports up to 256 lbs (120 kg).
● Before each ride, especially if you may travel a long distance, check the front tire for proper inflation
check all cables for damage, and test the brakes. Do not ride if any part of the scooter is damaged or
malfunctioning.
● Only operate the ESKUTE ES MAX where permitted. Local laws may restrict where you may ride.
● In compliance with UL2272 standards, power to the ESKUTE ES MAX motorized wheel may cut off
during continuous uphill travel and/or other cases which cause the motor to overheat. If the motor
overheats, this safety feature will trigger automatically. Stop riding and allow~15 minutes before using the
motor again. In general, continuous uphill travel at 20° slopes for long periods of time is not
recommended.

6.1 Getting Ready

First, choose a suitable venue for riding. Next, unfold the scooter in accordance with the instructions.
Start your scooter by pressing and holding the power button for 3~5 seconds.
● Slide your foot forward a few meters on the ground to activate the electric mode.(Push-Start mode.
Change mode via APP.)
● Moving forward with your scooter is as easy as pressing the throttle.
● Cruising is as simple as maintaining speed for at least 5-10 seconds. (It can be turned off via the
ESKUTE app.)
● Use the bell to alert pedestrians and other riders of your presence.
● Turn the headlight on/off by quick-pressing the power button twice.
● Switch gears between ECO,D, and S by quick-pressing the power button once.Each gear has different
speed. Gear ECO's max. is 5 mph, Gear D's is 10 mph, and Gear S's is 18.6 mph. (New feature - Walk
Assist Mode: You can apply this ride mode while walking down the street with your friends.)
● The display shows how much battery power is left.
- 05 -