Tabla de contenido
ENGLISH
INSTALLATION INSTRUCTIONS
PRESTOTEM "TOUCH" SHOWER PANEL WITH/WITHOUT THERMOSTATICS
0) PRECAUTIONS FOR USE (The product guarantee depends on the respect for these rules)
INSTALLATION and START UP
For products delivered with filters, these must be installed in accordance with the instructions. Before commissioning any of our
valves, it is essential to carefully bleed the pipes that can damage the mechanisms or water passages (PRESTO® heads that can be
dismantled from front). Recommended operating pressure according to NF EN 816: 1 to 5 bars.
CLEANING
The chrome-plated coating of PRESTO® valves must be cleaned only withsoapy water.
Abrasive, acid, alkaline or ammonia-based household products are prohibited.
MAINTENANCE
Never lubricate the internal mechanism, particularly the caps and valve seals.
1) Fixed shower heads with swivel jets
2) Fixed shower heads with swivel jets with légionellose option
3) Feed
4) High
5) Built-in
6) Grey finish RAL 7035
7) Creamy white finish RAL 9001
8) Button + 3 screws
9) Filter Seal ½
10) Straight Shut-off Valve G1/2
11) Angle Shut-off Valve G1/2
12) Limiter Bushing G1/2
13) Flat seal G1/2
14) Flow regulator
15) Pin
16) Screw VBA TC 4x40 + washer
16 bis) Operation of the PRESTOTEM ''TOUCH '' panel
· The user activates the flow from the panel by lightly touching the control button.
· The flow stops instantaneously following another light touch.
· If the user does not request switching off of the water flow, it is stopped after 30 s.
Commissioning
· Before commissioning, activate several times to force the air out, and adjust the angle of the jet.
Weathering
· In case of installation in a freezing zone, the panel must be removed in winter.
! The panel is delivered with the battery connection disconnected.
During the commissioning, connect the battery to the button, then wait for a minimum of 15s before lightly touching the button.
17) Preparation
18) INSTALLATION
19) Bleed the pipes
20) Removal of the soap holder bottom part
21) Removal without soap holder for maintenance bottom part
22) 2.1m from the floor to the shower head precaution see covers page 12
23) Re-assembly while retaining the soap holder
24) Use without soap holder Installation of the button
25) Installation of the soap holder
26) Equipotential bonding: Connect the connecting wire to an open lug D4 (not provided) to be inserted below this screw.
27) Hydraulic Connection
28) Top inlet
29) Built-in inlet
30) With Thermostatic mixing valve
31) Pre-mixed
32) Maintenance
Replacing the solenoid valve
Part no. See general catalogue
−
Turn off the water inlet
−
Remove the panel (see pages 3 and 4)
33) Reassembly in reverse order
34) Replacing the Shower Grille Part number: 90185 (grille only) Part number: 90184 (grille + screw + limiter)
Replacing the Shower Grille
Unscrewing expansion screw
−
Replacement
−
35) CHANGING THE BATTERY
36) Replacing the ''TOUCH'' control button Part no. See general catalogue
· Turn off the water inlet.
· Remove the panel (see pages 3 and 4).
· Disconnect the wiring, remove the button.
· Reinstall in the reverse order to that of removal.
· Reinstall the panel, open the water inlet.
· Wait for 10 s, the panel is operational.
39) Commissioning
-Bleed the pipes
-Connect and open the shut-off valves fitted with filter seals
-Trigger several times to force the air out Weathering
-In case of installation in a freezing zone, the panel must be removed in winter Flow
-Delivered with a flow limiter 10 l/min
40) ADJUSTMENT AND MAINTENANCE OF THE THERMOSTATIC CARTRIDGE
The Mixing valve allows the user to select the temperature of the lukewarm water, between
the cold water temperature and the lukewarm temperature preset at 38°C.
41) MODIFICATION OF THE MAX OPERATING TEMPERATURE
42) + Hot
Tabla de contenido
