Makita CL002G Manual De Instrucciones página 13

NOTE: You can change the suction power before
turning on the cleaner.
NOTE: The cleaner starts the operation with the
same suction power as the last operation.
Lighting up the lamp
CAUTION:
Do not look in the light or see the
source of light directly.
To turn on the lamp, push the suction power change
button. The lamp goes off in approximately 10 seconds.
While the cleaner is running, the lamp turns on.
The lamp goes out approximately 10 seconds after
stopping operation.
NOTE: When the remaining battery capacity gets low,
the lamp starts blinking. The timing, at which the lamp
starts blinking depends on the temperature at work
place and the battery cartridge conditions.
► Fig.5: 1. Suction power change button 2. ON/OFF
button 3. Lamp
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Dust bag and paper filter
Install either dust bag or paper filter before using cleaner.
Use the dust stopper when installing either dust bag or paper filter.
Dust bag are usable many times repeatedly by cleaning it out.
Paper filter is a throw-away type. Throw away the entire
paper filter without emptying when it has become full.
NOTICE:
To prevent dust from getting into the
motor:
• Make sure that the dust bag or paper filter is
installed before use.
• Insert the dust stopper together with the
dust bag or paper filter all the way into the
slots when installing them.
• Do not use a broken or ripped bag.
Otherwise the motor may be broken.
NOTICE:
Do not fold the cardboard at its open-
ing when installing the paper filter.
NOTICE:
Never throw away the dust stopper
because it needs to be used repeatedly whenever
either the dust bag or the paper filter is used.
NOTICE:
The paper filter for the cleaner is an
important component for maintaining the tool
performance. Using other than the genuine paper
filter may cause smokes or ignition.
NOTE: When the dust bag or the paper filter is not
installed in the cleaner, the front cover does not close
completely.
► Fig.6
Installing dust bag
Use the dust stopper when installing dust bag. Be
careful not to take the upper side for the lower side by
mistake because they are different each other.
► Fig.7: 1. Upper side of dust stopper 2. Lower side of
dust stopper
1. Insert the protrusion of the dust bag into the lower
groove on the dust stopper as shown in the figure.
► Fig.8: 1. Dust stopper 2. Lower groove 3. Dust bag
There is no distinction between the upper and lower
sides of the dust bag. You may insert its protrusion of
either side into the lower groove of the dust stopper.
► Fig.9: 1. Lower groove
2. Overlap the frame of dust stopper with that of the
dust bag.
► Fig.10
3. Place the dust stopper and the dust bag together
into the cleaner cavity in the same direction of arrow on
the dust stopper. Insert them all the way into the slots in
the cleaner cavity.
► Fig.11
4. Spread the cloth part of the dust bag inside the cleaner.
► Fig.12
5. Close the front cover completely.
► Fig.13: 1. Front cover
Installing the paper filter
Use the dust stopper also when installing paper filter.
Be careful not to take the upper side for the lower side
by mistake because they are different each other.
► Fig.14: 1. Upper side of dust stopper 2. Lower side
of dust stopper
1. Unfold the entrance of the paper filter before
setting it on the dust stopper.
► Fig.15
2. Insert the protrusion of the paper filter into the
lower groove on the dust stopper as shown in the figure.
► Fig.16: 1. Dust stopper 2. Lower groove 3. Paper filter
There is no distinction between the upper and lower
sides of the paper filter. You may insert its protrusion of
any side into the lower groove of the dust stopper.
► Fig.17: 1. Lower groove
3. Overlap the frame of dust stopper with that of the
paper filter.
► Fig.18
4.
Place the dust stopper and the paper filter
together into the cleaner cavity in the same direction of
arrow on the dust stopper. Insert them all the way into
the slots in the cleaner cavity.
► Fig.19
5.
Spread the container part of the paper filter inside
the cleaner. ► Fig.20
6. Close the front cover completely.
► Fig.21: 1. Front cover
13 ENGLISH