Product Specifications - AQUAVISTA 10-B421-AV Instrucciones De Montaje

PRODUCT SPECIFICATIONS

Max. Flow Rate: 1.2 GPM (4.54 LPM) at 60 PSI
ASME A112.18.1/CSA B125
NSF 61-9
Polished chrome finish
ASSEMBLY INSTRUCTIONS
1.
Turn off water at the supply valve
under the sink or at the main water
supply. Disconnect the supply lines to
the faucet and remove the old faucet.
Clean and dry the surface area
where the new faucet will be
mounted.
2. Ensure the gasket (2.1) is in place on
the bottom of the faucet body (A).
Apply a thin bead of silicone sealant
to the underside of the gasket (2.1)
on the faucet body (A). Insert the
faucet body (A) through the
mounting holes in the sink (2.2).
Secure the faucet body (A) to the
sink using the mounting nuts (D).
3. To connect the water supply, use
1/2 in. IPS faucet supply lines (3.1)
or coupling nuts (3.2) with 3/8 in.
O.D. ball-nose risers (3.3).
Wrap thread seal tape around each
faucet shank (3.4) in a clockwise
direction. Use a wrench to tighten
each supply line (3.1) fitting or
coupling nut (3.2) to the faucet
shanks (3.4). Do not overtighten.
4. Remove the stopper (4.1) and
flange (4.2) from the pop-up drain
assembly (C). Screw the attached
mounting nut (4.3) down the pop-up
drain assembly (C) and then push the
gasket (4.4) down.
1
2
A
2.1
2.2
D
3
3.4
3.3
3.1
3.2
4
4.1
4.2
4.4
4.3
C
Washerless cartridges
Manufactured to include no more than 0.25% weighted average lead content
on wetted surfaces
Total weight of item: 1.66 lbs.
5. Apply silicone to the underside of
the flange (5.1). From underneath
the sink, insert the pop-up drain
assembly (C) into the drain opening
(5.2) in the sink. From above the
sink, screw the flange (5.1) onto the
pop-up drain assembly (C). The
pivot hole (5.3) must face the back
of the sink.
Use groove joint pliers to tighten
the nut (5.4) or the sealant may not
seal properly. Do not overtighten.
Clean away any excess silicone.
Open the easy install rotating
clip (5.5).
6. Insert the stopper (6.1) down into
the pop-up drain assembly (C).
Install the horizontal rod (6.2)
from the lift rod assembly (B) into
the pivot hole (6.3) in the pop-up
drain assembly (C) as shown in
figure B. Make sure the horizontal
rod (6.2) is inserted completely
into the pop-up drain assembly
(C) and that it engages with the
stopper (6.1), as shown in figure A.
Close the easy install rotating
clip (6.4).
7. If the horizontal rod (7.1) is too
long, as shown in figure A, the
length can be adjusted.
As shown in figure B, remove the
clip (7.2) from the horizontal rod
(7.1). Slide the plastic portion of
the rod to adjust to the desired
length. The excess length (7.3) can
be removed where perforated by
snapping it off with pliers or cutting
it off with a saw.
After the plastic portion of the
horizontal rod (7.1) is positioned
properly, reinstall the clip (7.2) as
shown in figure C.
2
5
5.1
5.2
5.4
C
5.3
5.5
6
6.2
6.1
Figure A
6.1
B
6.2
6.3
C
6.4
6.3
Figure B
7
Figure A
7.1
7.3
7.1
Figure B
7.2
Figure C 7.1
7.2
HomewerksWW.com