Makita CL108FD Manual De Instrucciones página 12

Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
► Fig.3: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
Indicator lamps
Lighted
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Switch action
► Fig.4: 1. ON/speed change button 2. OFF button
To start the cleaner, simply push the ON/speed change
button. To switch off, push the OFF button.
You can change the cleaner speed in three steps by
pushing the ON/speed change button.
The first push on this button is for high speed mode, the
second push for max speed mode and the third push for
normal speed mode. Each push on this button repeats
the high/max/normal speed cycle alternatively.
Lighting up the lamp
CAUTION:
Do not look in the light or see the
source of light directly.
► Fig.5: 1. ON/speed change button 2. OFF button
3. Lamp
To turn on the lamp, push the ON/speed change button.
Push the OFF button to turn off the lamp. During the
tool actuating, the lamp turns on.
When the remaining battery capacity gets low, the lamp
starts blinking.
NOTE: The timing, at which the lamp starts blinking,
depends on the temperature at work place and the
battery cartridge conditions.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Remaining
capacity
Off
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Type of filter
Normal filter
► Fig.6: 1. Capsule 2. Prefilter 3. Filter
High performance filter
► Fig.7: 1. Capsule 2. High performance filter
Disposing of dust
CAUTION:
Empty the cleaner before it
becomes too full, or the suction force weakens.
CAUTION:
Be sure to empty the inside of the
cleaner itself of dust. Failure to do so may cause the
filter to be clogged or the motor to be damaged.
Disposing of dust for normal filter
In order to drop dust sticking on the filter in the capsule,
tap the capsule 4 or 5 times with your hand. ► Fig.8: 1. Capsule 2. Suction inlet
Point the suction inlet downwards, turn the capsule in
direction of the arrow as illustrated, and disconnect the
capsule slowly and straight.
► Fig.9: 1. Capsule 2. Suction inlet
NOTE: Be sure to set a garbage bag beneath the
capsule, as dust may spill out when the capsule is
opened.
Remove accumulated dust from inside of the capsule
and off of the prefilter.
► Fig.10: 1. Prefilter 2. Capsule
Twist the prefilter in direction of the arrow to unfasten the
securing lip from the cleaner unit and then pull off the prefilter.
► Fig.11: 1. Prefilter 2. Securing lip
Clean out fine dust from the prefilter. And then, pull off
the filter and lightly tap it to remove dust.
► Fig.12: 1. Filter 2. Prefilter
Disposing of dust for high
performance filter
In order to drop dust sticking on the filter in the capsule,
tap the capsule 4 or 5 times with your hand.
Now point suction inlet downwards, turn capsule in
direction of arrow in diagram, and disconnect capsule
slowly and straight.
► Fig.13: 1. Capsule 2. Suction inlet
NOTE: Dust may spill out when capsule is opened, so
be sure to set a garbage bag beneath capsule.
Remove accumulated dust from inside of capsule and
off of high performance filter.
► Fig.14: 1. Capsule 2. High performance filter
Twist high performance filter in direction of arrow to unfas-
ten securing lip from cleaner unit and then pull off the filter.
► Fig.15: 1. Securing lip
Clean out the fine dust and lightly tap to dislodge dust
from high performance filter.
12 ENGLISH