Operating The Appliance - LUND 67112 Manual Original

GB
the appliance, you must discontinue using it. In this case, the appliance must be taken to an
authorised service centre or replaced by yourself, if this is permitted by the user's manual.
Turn off the appliance and unplug the power cord from the wall socket before you start
any work on replacing, cleaning, or adjusting. Switch off the appliance before replacing
the accessories and unplug the power cord from the socket. This appliance may be used by
children of at least 8 years of age and by persons with reduced physical, mental abilities and
persons with no experience or knowledge of the appliance, if supervised or instructed on its
safe use so that the risks associated with it were understandable. Children should not play
with the appliance. Children should not be allowed to clean or maintain the product without
supervision.The appliance is intended for home use only. Do not use the vacuum cleaner
on people and animals, do not put the inlet of the suction nozzles near eyes and ears. Do
not pass through the power cord with the vacuum cleaner, do not stand on the power cord.
This can damage the cable and cause electrical shock.Check the condition of the vacuum
cleaner fi lters before each use. It is forbidden to use the vacuum cleaner without fi lters or
with damaged fi lters. Before each use, check the passability of the hose, pipes and suction
nozzles. If a decrease in suction power or increased noise is noticed during operation, the
passability of the above mentioned elements and the level of fi lling of the dust container
must be checked.Do not vacuum cigarette butts, matches, hot ashes. Avoid pulling in sharp
objects such as needles, nails, pins or staples. Do not vacuum water or other liquids. Do not
vacuum wet waste. Do not vacuum fi ne dust, e.g. fl our, gypsum, printer toner, etc. Do not use
the vacuum cleaner for cleaning industrial waste, e.g. sawdust, debris, metal fi lings, etc.The
vacuum cleaner must not be used in a dust extraction system where the dust is generated
during operation of other tools, e.g. grinding, cutting, polishing, etc. When vacuuming, static
charges may occur on the appliance. This is normal, especially when cleaning in low humid-
ity conditions. In order to minimise this phenomenon, it is necessary to periodically touch the
grounded, metal objects around the house, e.g. radiators, with the pipe and to increase the
humidity in the room to be cleaned.

OPERATING THE APPLIANCE

CAUTION! Turn off the appliance and unplug the power cord from the socket during all equipment assembly and disassembly activities.
Appliance assembly and disassembly
Take the vacuum cleaner, the dust container and accessories out of the packaging and remove all packaging components. Begin
assembly of the vacuum cleaner.
Slide the handle of the vacuum cleaner into the slots of the drive housing (II). Make sure that the connection is locked and cannot
be disconnected other than by pulling back the lock and holding it in place (III).
Before fi rst use, make sure that the container has all components and is correctly assembled.
If the container is mounted on a vacuum cleaner, it must be removed. Turn the container in the direction indicated by the open
padlock symbol (IV) and then remove the container from the vacuum cleaner.
Remove the internal paper fi lter from the container (V) and then the external plastic fi lter (VI). The external fi lter has been shaped
in such a way that it can only be installed in one correct position (VII). Slide the internal fi lter into the external fi lter so that the inter-
nal fi lter fl ange rests on the external fi lter housing (VIII). Check the condition of each fi lter and the condition of the gasket around
the internal fi lter fl ange to ensure that no components are damaged. The container has a snap-on lid on the front, make sure it is
closed. The lid is opened by pressing the latch (IX).
Attach the container with the closed lid and the installed fi lters to the vacuum cleaner. Attach the container housing to the drive
housing so that the arrow on the drive housing is in line with the arrow on the container labelled "Align", then rotate the container in
the direction indicated by the open padlock symbol (X). Make sure that all latches on the drive housing are located in the recesses
of the container housing. Make sure that the shape of the drive housing is extended by the container housing (XI).
The handle housing can be equipped with an adapter which allows you to hold some accessories, always within reach. Slide the
O R I G I N A L I N S T R U C T I O N S
13