Neonato PURO Instrucciones De Uso página 30

By lifting the wheel and applying the pushchair brake, the catch
(in light blue) can be seen which locks the wheel when the brake
is applied.
6b. TO LOOSEN THE BRAKE: if when the rear wheel turns it
makes a noise or it tends to lock, loosen the wheel cable by
turning the device (in red) located on the housing of the wheel in an
anti-clockwise direction. Block the device in the position required by
turning the small wheel (in green) in a clockwise direction. Repeat the
operation on the other wheel if necessary.
6c. TO TIGHTEN THE BRAKES: if the brake does not lock the wheel, release
the device (in red) by turning the small wheel (in green) in an anti-clockwise
direction. Lengthen the cable by turning the device (in red) in a clockwise
direction. Repeat the operation on the other wheel if necessary.
7. ADJUSTING THE HANDLE: hold a foot on the rear bar, then push button "T"
and at the same time adjust the handle until you reach the desired position.
8. FRONT SWIVEL WHEELS: push the lever "X" upwards to make the wheels
swivel, push the lever downwards to align them.
9. FITTING THE BASKET
10. POSSIBLE COMBINATIONS:
The diagram shows the age/weight for the use of the various features and
their correct assembly. The pushchair is reversible: it can be fitted on the
chassis both rear facing so the seat is facing Mum or Dad or forward facing
so the seat looks towards the road.
11. FITTING/REMOVING THE CARRYCOT "A" FROM THE CHASSIS:
11a. Place the adapters "Y" inside their housings on the chassis. Pay attention
to put them in the right direction (1)! Fit the carrycot through the adapters
until a "click" is heard (2).Make sure the carrycot is securely locked (3).
11b. Press first button "A" then "B" on both sides of the adapters (1) and then
lift up the carrycot (2). Button "B" will keep engaged once pressed, while
button "A" must be pressed while the carrycot is lifted up.
12. USING THE CARRYCOT "A":
12a. To fasten the hood to the carrycot, insert the metal tabs into the slots at
the sides of the handle. Close the press fasteners on the back of the hood.
12b. By opening the flaps located under the body, the carrycot converts into
a rocking cot.
12c. The angle of the handle can be adjusted by pressing the buttons at the
sides of the handle at the same time (safety mechanism).
12d. Aerated base.
12e. To raise the backrest, push the handle located underneath inwards
towards the body. To lower it, press the handle slightly inwards, lift it and
move it back to the required position.
12f. To fit the footmuff, close the press fasteners as shown in the diagram.
12g. The hood is adjustable in height.
29
12h. To remove the hood, release the ends of the metal tabs.
13. CAR SAFETY KIT V483 (OPTIONAL, ONLY FOR CARRYCOT "A"):
13a. Car safety kit.
13b. Insertion of the impact absorbers.
13c. Fitting the abdominal belt. Insert the two buckles "A" in their respective
slots "B" located on the bottom of the carrycot (1,2). Once they have been
inserted, turn them and then secure parts "A" to the bottom of the carrycot (3).
13d. Closure and adjustment of the abdominal belt.
13e. Correct passage of plates "D" in belts "C". The plates must be
positioned close to the seat of the car.
13f. Tightening the belt.
13g. Correct position of the carrycot.
14. FITTING THE CARRYCOT "B":
Execute the sequence shown in the picture (14a - 14b - 14c - 14d - 14e).
TO FASTEN THE HOOD TO THE CARRYCOT, SEE FIGURE 22.
15. FITTING/REMOVING THE CARRYCOT "B" FROM THE CHASSIS:
Execute the sequence shown in the picture.
FITTING/REMOVING THE CAR SEAT FROM THE CHASSIS:
16. Place the adapters "Y" inside their housings on the chassis. Pay attention
to put them in the right direction! Fit the car seat through the adapters and
push until a "click" is heard. Make sure the car seat is securely locked.
17. Press first button "A" then "B" on both sides of the adapters (1) and then
lift up the car seat (2). Button "B" will stay down once pressed, while button
"A" must be kept pressed when the car seat is lifted.
FOR USE OF THE CAR SEAT READ THE RELEVANT INSTRUCTION BOOKLET.
REMOVING THE ADAPTERS FOR CARRYCOT AND CAR SEAT
18. Push the button (1) and at the same time lift them up (2).
ASSEMBLING THE SEAT PAD
19. Execute the sequence shown in the picture (19a - 19b - 19c).
20. 5 POINT HARNESS ON THE PUSHCHAIR: adjusting the harness (20a) and
open the buckle (20b).
6-12 MONTHS, USE OF THE SEAT REARWARD FACING:
It is advisable to use the seat in the rearward facing position to enable Mum
to keep an eye on baby while still young (6-12 months) during walks.
FITTING THE SEAT REARWARD FACING (6-12 months):
21. Fit the seat unit to the chassis, by putting it into the relevant housings.
Push it until a "click" is heard.
22. USING THE HOOD:
Fix canopy attachments on the seat unit frame. ATTENTION: make sure to
match the nick on the chassis with the slot on the hood (1). Fasten the zip
by joining the canopy to the seat unit (2). To remove the canopy, unfasten
the slots and undo the zip of the canopy.
23. Fit the bumper bar into the housing at the front of the armrests. A "CLICK"
will be heard once button "O" is fitted correctly inside the housing. To remove
the bumper bar, press on buttons "O" and pull away from the pushchair.