Skil F0151840 Serie Manual Original página 11

EXPLANATION OF SYmBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Mounting/removing router bits 6
! switch off the tool and disconnect the plug
! ensure that router bit shaft is perfectly clean
! ensure that collet size (6 mm, 8 mm) corresponds
with shaft size of router bit
- turn tool upside down
- lock shaft by pushing shaft lock A (rotate collet nut B, if
necessary) and hold it while you
FOR MOUNTING:
- loosen collet nut B with wrench C
- insert bit 3/4 in collet
- tighten collet nut firmly with wrench C
FOR REMOVING:
- loosen collet nut B with wrench C
- remove bit
- release shaft lock A
! for loosening router bit it may be necessary to
tap collet nut with wrench 7
! never tighten collet nut, if there is no router bit in
collet; collet may be damaged
• Changing collet
! switch off the tool and disconnect the plug
! ensure that collet shaft is perfectly clean
- loosen collet nut B 2 or 3 turns
- tap collet nut B with wrench C
- remove collet nut B and collet (lock shaft)
- turn tool upside down
- insert new collet in collet shaft
- mount collet nut B (lock shaft)
! never tighten collet nut, if there is no router bit in
collet; collet may be damaged
• Adjusting routing depth 8
! switch off the tool and disconnect the plug
- ensure that the small rod within depth gauge D
extends approximately 3 mm (use fine-adjustment
knob E) 8a
- rotate turret F so that its highest position clicks into
place right under depth gauge D (for zeroing) 8b
- loosen knob G so that depth gauge D drops onto
depth stop turret F 8b
- place tool on workpiece
- loosen locking lever H 8c
- push tool down until router bit is in contact with
workpiece 8d
- tighten locking lever H 8e
- routing depth is now set to 0 mm (note value as
indicated on depth scale)
- raise depth gauge D as many mm as the desired
routing depth, and tighten knob G 8f
- loosen locking lever H and guide the tool back up
again
- use fine-adjustment knob E for setting the routing
depth more precisely (0-10 mm)
- with depth stop turret F the routing depth can be
increased by 5 or 10 mm respectively
! re-adjust the routing depth after having changed
router bits
• Speed control 9
For optimal routing results on different materials
- select routing speed with wheel J (also while tool is
running)
- use table 0 as reference for determining the right
routing speed
- before starting a job, find the optimal speed by testing
out on spare material
! after longer periods of working at low speed,
allow the tool to cool down by running it for
approximately 3 minutes at high speed with no
load
• Dust suction !
- connect vacuum cleaner to extension K
! never let the vacuum cleaner hose interfere with
the routing operation
• Operating the tool @
- adjust routing depth
! always hold the tool firmly with both hands
! while working, always hold the tool at the
grey-coloured grip area(s)
- place tool on workpiece
- switch on the tool by pulling trigger L
- lock the switch for continuous use by pressing button
M
! before the router bit reaches the workpiece, the
tool should run at full speed
- loosen locking lever H and slowly push tool down until
depth gauge D reaches depth stop turret F
- tighten locking lever H
- carry out the routing procedure with uniform feed rate
- use the tool with its base-plate flat on the workpiece
- as a general rule one should pull the tool, not push it
- unlock the switch by pulling again trigger L and then
releasing it
- after finishing the work, loosen lever H and guide the
tool back into the upper starting position
• Handle position adjustment #
- unlock both handles by sliding knobs N to the outer
position and hold them while turning the handles into
the desired position
- release both knobs N until they snap-lock (4 positions
possible)
• Proper guiding $
- keep in mind that router bit turns clockwise
- guide tool so that bit turns into the workpiece, not away
from it
• Mounting adapter plate P (for copying with a template) %
• Mounting parallel guide Q ^
- insert parallel guide rods V through holes in base-plate
R
- slide parallel guide to desired width and fasten it with 2
knobs W
11