Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Tabla de contenido
Manuales relacionados para Biamp AMP-A460H
Resumen de contenidos para Biamp AMP-A460H
- Página 1 AMP-A460H OPERATION MANUAL NOVEMBER 2016...
- Página 2 A460H - Setup and Installation Setup and Use CAUTION All speaker wiring connections should be made by qualified personnel and with the amplifier power removed. The 100V output requires Class 3 wiring. Please refer to a qualified electrician or other qualified person according to local codes. Installation Each unit requires a space of 1.75 inch (44mm) high, 8.7 inch (221mm) wide with 10.47 inch (266mm) depth and may be mounted on a flat surface or in a rack enclosure.
- Página 3 This plug is the main disconnecting device and should remain readily operable. There are no user interchangeable parts. Please contact Biamp Technical Support or your local distributor for all service requirements.
- Página 4 A460H – Connections Input Wiring All wiring examples are Single Channel Connections Balanced Input Connections Unbalanced Input Connections Speaker Wiring All wiring examples are Single Channel Connections Single Channel 4 or 8 ohm Bridged mode 4 or 8 ohm Bridged mode 70/100V...
- Página 5 A460H - Setup Gain staging The amplifier channels are intended to be used with the default output blocks available in Tesira Software. Care should be taken to match the speaker load to the output capabilities (wattage) of the amplifier. For example, if a low-impedance single channel speaker load is 60 watts you are perfectly matched at the nominal input level.
- Página 6 A460H - Amplifier Current Draw AMP-A460H 1/8 Power Bridged Constant Voltage 4 ohm 8 ohm 4 ohm 8 ohm 100V Current Draw Amps Amps Amps Amps Amps Amps 100VAC 50Hz 100VAC 60Hz 120VAC 60Hz 230VAC 50Hz 240VAC 50Hz 1/3 Power...
-
Página 7: Specification Table
A460H Specifications Specification Table Number of Channels Power 100V-240V, 50Hz / 60 Hz Maximum Rated Output (Single Channel Driven): Environment: 4Ω, 8Ω Cooling Convection Bridged 4Ω, 8Ω: 120W Bridged 70V/100V: Ambient Operating Temperature 32-104°F (0-40°C) 120W Humidity 95%, non-condensing THD +N 20Hz-20kHz, at rated power: <0.3% (all power ratings at rated... -
Página 8: Important Safety Instructions
To reduce the risk of fire, use only No. 26 AWG solid copper wire for telecom circuit connections. Intended for Installation and Service by Skilled Personnel Only: CAUTION – To reduce the Risk of Electric Shock, Installation and Service of Biamp Products should be conducted only by Skilled Persons who are Biamp Qualified Audio Installation Professionals. -
Página 9: Instrucciones De Seguridad Importantes
Para la instalación y mantenimiento solo por parte de personal calificado: PRECAUCIÓN – Para reducir el riesgo de descarga eléctrica, la instalación y el mantenimiento de los productos Biamp deben ser realizados por personas calificados que formen parte de los Profesionales capacitados en la instalación de audio de Biamp. -
Página 10: Consignes De Sécurité Importantes
Installation et interventions réservées au personnel compétent: MISE EN GARDE – Pour limiter les risques d’électrocution, l’installation des produits Biamp et les interventions sur ces produits doivent être réalisées uniquement par du personnel compétent faisant partie des professionnels d’installation audio qualifiés de Biamp. -
Página 11: Wichtige Sicherheitshinweise
Brandrisiko zu reduzieren. Ausschließlich für Einbau und Wartung durch geschultes Personal vorgesehen: VORSICHT – Zur Verringerung der Stromschlaggefahr sind Einbau und Wartung von Biamp-Geräten ausschließlich durch geschulte Personen, bei denen es sich um von Biamp geschulte Audio-Fachleute handelt, vorzunehmen. Führen Sie keine anderen als die in der Betriebsanleitung angegebenen Wartungsarbeiten aus, vorausgesetzt, Sie wurden hierfür geschult. - Página 12 警告 – 由市电供电的产品采用了安全接地技术，必须与正确接地的市电插座连接，才能提供接地防护。 断开设备连接 – 市电插头可用于断开 市电电源且必须保持时刻可运行状态。 小心 – 在提供了 POTS 电话接口选项时，必须由训练有素的人员将电话接口与本设备的电信回路进行连接。为减少火灾风险，只能使用 26 号 AWG 实心铜线连接电话端口。 只适用于专业技术人员来执行的安装和服务： 小心 – 为减少电击带来的风险，Biamp 产品的安装和服务应该只能由 Biamp 音频安装专业技术人员来执行。 除非您是专业技术人员，否则不能执行未包含在操作说明中的任何服务。 在打开产品之前，专业人员必须先断开交流市电电源。 小心 – “辅助电源”的安装步骤只适用于专业技术人员，而且必须遵循所有的本地法规。 • 对于美国，国家电气法规 ANSI/NFPA 70。 • 对于加拿大，加拿大电气法规第 1 部 CSA C22.1 第 2-128、12-010(3) 和 12-100 节。...
- Página 13 위험을 줄이기 위해서는 전기 통신 회로 연결은 26번 AWG 솔리드 동선만 이용하십시오. 공인 전문가의 설치 및 서비스: 주의 – 전기 충격의 위험을 줄이기 위해, Biamp 제품의 설치 및 서비스는 Biamp 공인 오디오 설치 전문가에게 의뢰해야 합니다. 전문 인력이 아닌 경우, 작업 지침에 담긴 내용 이외의 사항에 대해 서비스를 제공하면 안됩니다.
- Página 14 .لتمديدات روابط دائرة االتصاالت AWG 26 :هذا الجهاز معد للتركيب والصيانة من قبل الموظفين الماهرين فقط Biamp إال من قبل األشخاص المهرة وهم المهنيون المؤهلون تنبيه - للحد من خطر حدوث صدمة كهربائية، ينبغي أال يتم تركيب وصيانة منتجات .Biamp في...
-
Página 15: Importantes Instruções De Segurança
Destinado para Instalação e Manutenção apenas por Pessoal Qualificado: ATENÇÃO – Para reduzir o risco de choque elétrico, a instalação e a manutenção dos produtos Biamp devem ser realizadas somente por pessoas qualificadas, que são profissionais de instalação de áudio qualificados da Biamp. -
Página 16: Важные Инструкции По Технике Безопасности
одножильный медный провод типа 26 AWG. Предназначено для установки и обслуживания только опытным персоналом ПРЕДОСТЕРЕЖЕНИЕ! Для снижения риска поражения электрическим током установку и обслуживание устройств Biamp должны выполнять только лица, которые являются опытными специалистами по установке аудиосистем Biamp. Не проводите какое-либо обслуживание, помимо указанного в инструкциях по эксплуатации, если вы не обладаете соответствующим опытом и... - Página 17 RoHS COMPLIANT This Biamp product, including all attendant cables and accessories supplied by Biamp, meets all requirements of EU Directive 2011/65/EU (RoHS2). RoHS Materials Content Declaration document may be obtained at www.biamp.com (This information is presented to comply with the requirements of Chinese law SJ/T11363-2006) 有害物质表...
- Página 18 The Warranty Period for the products described in this manual shall be five (5) years. The Warranty Period begins (a) the date of the original end user’s purchase from an authorized Biamp Systems dealer or (b) six months after the product is first shipped from Biamp Systems’...