Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Use of this kit upgrades all PP1200, PP1250, PP1260, PP1400, and PPT-2100/2400, PPFD-2400 Models.
NOTE: Do not bend or deform drive shafts while servicing them.
Never reuse old holes in drive shaft or shaft connector assembly.
1. Saw the old shaft connector assembly off drive shaft flush at shaft connector end and remove all burrs. Lower drive shaft
length must be a minimum 57 in. after cutting.
2. Center punch the outside diameter of the shaft connector sleeve (A) approximately 3/8 in. from the open end. Rotate the
sleeve 90 degrees and make a second center punch approximately 5/8 in. from the open end.
3. Slide the shaft connector assembly onto the lower drive shaft (B)
as far as it will go.
4. Drill through both center punches with a 5/64 in. drill. Finish the
holes with a #40 drill (0.98 in. drill).
5. Countersink one end of each hole with a 1/8 in. drill to a depth of
1/32 in.
6. Tap in straight pins (C) (P/N V620000000) through both holes.
Peen the small end of pins in each countersunk hole to properly
hold pins.
SUP22203704
Use of this kit upgrades all PP1200, PP1250, PP1260, PP1400, and PPT-2100/2400, PPFD-2400 Models.
NOTE: Do not bend or deform drive shafts while servicing them.
Never reuse old holes in drive shaft or shaft connector assembly.
1. Saw the old shaft connector assembly off drive shaft flush at shaft connector end and remove all burrs. Lower drive shaft
length must be a minimum 57 in. after cutting.
2. Center punch the outside diameter of the shaft connector sleeve (A) approximately 3/8 in. from the open end. Rotate the
sleeve 90 degrees and make a second center punch approximately 5/8 in. from the open end.
3. Slide the shaft connector assembly onto the lower drive shaft (B)
as far as it will go.
4. Drill through both center punches with a 5/64 in. drill. Finish the
holes with a #40 drill (0.98 in. drill).
5. Countersink one end of each hole with a 1/8 in. drill to a depth of
1/32 in.
6. Tap in straight pins (C) (P/N V620000000) through both holes.
Peen the small end of pins in each countersunk hole to properly
hold pins.
SUP22203704
Shaft Connector Kit P021006370
Assembly Instructions
1/4 in. Shaft Connector to Drive Shaft Assembly
Shaft Connector Kit P021006370
Assembly Instructions
1/4 in. Shaft Connector to Drive Shaft Assembly
B
C
C
A
99922203704
08/03
B
C
C
A
99922203704
08/03
Resumen de contenidos para Echo P021006370
- Página 1 Shaft Connector Kit P021006370 Assembly Instructions 1/4 in. Shaft Connector to Drive Shaft Assembly Use of this kit upgrades all PP1200, PP1250, PP1260, PP1400, and PPT-2100/2400, PPFD-2400 Models. NOTE: Do not bend or deform drive shafts while servicing them. Never reuse old holes in drive shaft or shaft connector assembly.
- Página 2 Juego de conector de eje P021006370 Instrucciones de montaje Montaje del conector de eje de 1/4 pulg al eje de impulsión El uso de este juego permite actualizar todos los modelos PP1200, PP1250, PP1260, PP1400, y PPT-2100/2400, PPFD-2400. NOTA: No doble ni deforme los ejes de impulsión mientras efectúa el servicio de los mismos.
- Página 3 Instructions de montage du kit de connecteur d’arbre P021006370 Connecteur d’arbre de 1/4 et arbre moteur Utiliser ces mises à jour de kit des modèles Power Pruner série PP1200, PP1250, PP1260, PP1400, et PPT-2100/2400, PPFD-2400 REMARQUE : Veiller à ne pas déformer les vis sans fin pendant l’entretien.
- Página 4 Si necesita asistencia o tiene dudas referentes a la aplicación, operación o mantenimiento de este producto puede llamar al Departamento de asistencia de productos del consumidor de ECHO, 1-800-673-1558 de 8:00 de la mañana a 5:00 de la tarde (hora central estándar) de lunes a viernes.