XPR Access EX6P Manual Del Usuario página 5

PAIRING EX6P AND REMOTE RELAY UNIT / COUPLAGE EX6P ET UNITÉ DE RELAIS À DISTANCE /
ACCOPPIAMENTO DELL'UNITÀ EX6P E RELÈ REMOTO / EMPAREJAMIENTO DE EX6P Y LA UNIDAD DE RELÉ REMOTO
VERBINDEN DES EX6P MIT ABGESETZTER STEUEREINHEIT / KOPPELING EX6P EN EX TERNE RELAISEENHEID
RU2 (Optional)
2 Relay Remote Unit
and request-to-exit Button
EX6P + RU2
12V/24V
AC/DC
A
PB1
B
GND
GND
PB2
NO COM
TAMP1
TAMP2
NC2 NC1
COM2 COM1
NO2
NO1
A
Pink (RS485)
B
Violet (RS485) GND
+12V
EX6P + DINRTT
12 VDC
12V/24V
AC/DC
A
PB1
B
GND
GND
PB2
TAMP1
TAMP2
NC1
NC2
COM2 COM1
NO2
NO1
Exit Button
Black
Red
Pink
Violet
EX6P + RTT
+
12 VDC
-
12V/24V
AC/DC
A
PB1
Black
B
GND
GND
PB2
Red
TAMP1
TAMP2
Pink
NC1
NC2
Violet
COM2 COM1
NO2
NO1
max. 50 meters
DINRTT (Optional)
2 Relay Remote Unit
and request-to-exit Button
OR
RTT (Optional)
1 Relay Remote Unit
Secured Area
1
2
RU2
+
12 VDC
-
+12V
GND
+
+ + V
V -
-
1N4001
- Diode
DINRTT
NC2
1 2
(NO)
GND
+12V
-
+
B (RS485)
12 VDC
A
(RS485)
Red
COM
Yellow
White NO
Black GND
Brown 12V out
Pink A
(RS485)
Violet
B
(RS485)
RTT
Outside
1. Close the Jumper (or dip switch in RTT). The Unit beeps
continuously and the red led blinks.
2. Open the Jumper (dip switch)
3. Wait for Beep + OK Beep (short + short + long beep)
After the OK beep, the coupling is done.
1. Fermez le cavalier (ou l'interrupteur DIP dans le RTT). L'unité
émet un bip sonore continu et la LED rouge clignote.
2. Ouvrez le cavalier (interrupteur DIP)
3. Attendre le bip + bip Ok (bip court + court + long)
Après le bip Ok, le couplage est effectué.
1. Chiudere il ponticello (o l'interruttore DIP in RTT). L'unità
emette segnali acustici in modo continuo e il LED rosso
lampeggia.
2. Aprire il ponticello (interruttore DIP).
3. Attendere un segnale acustico + il segnale acustico di OK
(suono breve + suono breve +
Dopo il segnale acustico di OK, l'accoppiamento è pronto.
1. Cierre el puente (o el interruptor DIP en RTT). La unidad emite
un pitido continuo y el LED rojo parpadea.
2. Abra el puente (interruptor DIP)
3. Espere un pitido + el pitido de conformidad (corto + corto +
largo)
Tras el pitido de conformidad, el acoplamiento se ha realizado.
1. Jumper schließen (bzw. DIP-Schalter bei RTT). Das Gerät piept
und gleichzeitig blinkt die rote LED.
2. Jumper (DIP-Schalter) öffnen.
3. Piepsignal + OK Piepsignal abwarten (2 kurze + 1 langer Piepton)
Ertönt das OK Piepsignal, wurde die Verbindung erfolgreich
abgeschlossen.
1. De jumper sluiten (of dip-schakelaar in RTT). De eenheid piept
ON
1 2
continu en de rode led knippert.
2. De jumper openen (dip-schakelaar)
3. Wacht op een toon + OK-signaal (korte + korte + lange toon)
Koppeling vindt plaats na het OK-signaal.
EX6P
Standalone Keypad with
integrated proximity reader
suono lungo)
5