Tabla de contenido
Enlaces rápidos
FSE Fitting & Squaring
Machine
Model FSE 1.0
Mod. FSE
E.H. WACHS COMPANIES
100 Shepard St. Wheeling Il. 60090
600 Knightsbridge Pkwy., Lincolnshire, IL 60069
Enter Your Machine's Serial Number Here For
Proper Record Keeping and Ordering Reference.
Part Number:
Revision No:
i
Ser.No.
Patent Pending
18-MAN-02
3
Revised
February 2014
Tabla de contenido
Resumen de contenidos para Wachs FSE 1.0
- Página 1 FSE Fitting & Squaring Machine Model FSE 1.0 Mod. FSE Ser.No. E.H. WACHS COMPANIES 100 Shepard St. Wheeling Il. 60090 600 Knightsbridge Pkwy., Lincolnshire, IL 60069 Patent Pending Enter Your Machine's Serial Number Here For Proper Record Keeping and Ordering Reference.
-
Página 2: Tabla De Contenido
FSE Drive Motor ..................... Machining Instruction ..................Machining Tips ....................1 Bench Stand Removal & Setup ............... 1 Special Shoe Sets For FSE 1.0 ............... 10 SECTION VI.MAINTENANCE ........................ 10 SECTION VII.OPERATIONAL CHARTS & GRAPHS................SECTION VIII. TROUBLE SHOOTING CHART................ -
Página 3: Section I
FSE FITTING SQUARING MACHINE FSE ST ANDARD EQUIPMENT SECTION I • 1 FSE 1.0 with drive motor and cord • "T" handle allen wrench • 1 Tool bit • Operating Instruction Manual • Shipping Case... - Página 4 FSE FITTING SQUARING MACHINE SAFETY INSTRUCTIONS SECTION II Read the Following thoroughly before proceeding Since 1883, EH Wachs has built a reputation for qual- ALWAYS WEAR PROTECTIVE EQUIPMENT: ity and a commitment to consumer satisfaction. In accor- WARNING dance with this, Wachs must take on the added responsi- bility of doing our best to assure the safest use of our equip- ment.
- Página 5 Seit 1883 hat EH Wachs seinen Ruf für Qualität und Zufriedenstellung seiner Kunden aufgebaut. Wachs übernimmt demgemäß die Depuis 1883, la société EH Wachs a bâti sa réputation sur la qualité de ses produits et son engagement à satisfaire la clientèle.
- Página 6 INSTRUÇÕES DE SEGURANÇA TURVALLISUUSOHJEET Já desde 1883 que a EH Wachs tem vindo a criar uma reputação de qualidade e um compromisso de satisfação dos EH Wachs on tunnettu korkeasta laadusta ja tyytyväisistä asiakkaistaan jo vuodesta 1883. Wachs huolehtii myös siitä, että...
- Página 7 ANVISNING I SIKKERHED Siden 1883 har EH Wachs haft ry for deres kvalitet og varetagelse af kundtilfredshed og vil også gøre vort bedste for at sikre, at vore maskiner benyttes på en sikker og forsvarlig måde. Vi har lavet en liste over påmindelser, der skal bidrage til at skabe det sikrest mulige arbejdsmiljø. Vi anbefaler, at sikkerhedsforanstaltningerne på...
- Página 8 FSE FITTING SQUARING MACHINE SECTION III EC Declaration of Conformity Name and address of manufacturer (if different) E.H. Wachs Company 100 Shepard St. Wheeling, Il. 60090 USA Distributed in the EC by: Business address: We declare that the machine described below conforms with the EHSR of the machinery directive 89/...
- Página 9 FSE FITTING SQUARING MACHINE FSE SPECIFICATIONS SECTION IV The new Wachs FSE is a light- weight, base mounted, portable tool for precision end finishing on fittings and tubes in seconds. The FSE is capable of square, burr-free end preps from 1/8” (3.175 mm) through 1”...
- Página 10 FSE FITTING SQUARING MACHINE FSE SETUP & OPERATING PROCEDURES SECTION V Chuck Adjustment Screw Chuck Gib NOTE: Please refer to your Operator Manual for Tool Spindle further details regarding the operation of your Feed Nut Milwaukee or Metabo drill. Pipe Shoe Milwaukee Model (PN 18-015-00) Metabo Model (PN 30-031-00) SPEED CONTROLLER- Dial in your chosen motor...
-
Página 11: Shoe Selection, Installation And Removal Procedure
Figure 2 out. Tension screws with 1/8" allen key. Workpiece Clamping Procedure Drive Motors for the FSE 1.0 1. Retract clamping knob by turning counter clock- wise. 1. Motors for FSE: Milwaukee and Metabo. Milwau- kee has simple variable speed trigger. Metabo has 2. -
Página 12: Machining Tips
FSE FITTING SQUARING MACHINE FSE SETUP & OPERATING PROCEDURES (CONT.) SECTION V Bench Stand Removal & Setup Machining Tips 1. To remove stand, loosen 1/2-13 x 2-1/2" FHCS. To reinstall stand, slide FHCS through base plate and 1. For precision machined lengths leave motor off. Ro- support. - Página 13 FSE FITTING SQUARING MACHINE FSE OPERA TIONAL CHARTS & GRAPHS SECTION VII FSE SHOE SELECTION FSE SHOE SELECTION CHART CHART *Standard American Sizes *Standard Metric Sizes Part No. Workpiece O.D. Part No. Workpiece O.D. 18-403-00 .125” 18-403-36 6 mm 18-403-01 .188”...
- Página 14 FSE TROUBLE SHOOTING SECTION VIII Trouble Possible Cause Remedy Machine Won't Run ..... Power Unit Not Connected ......Check Power Cord & Connection Work Piece Shifts Under .... Loose Shoe Clamp ........... Check Tension on Shoe Clamp Handle Cutting Load. Poor Workpiece End Quality ..
- Página 15 FSE FITTING SQUARING MACHINE SECTION IX PARTS LISTS & EXPLODED VIEW DRAWINGS...
- Página 16 FSE HOUSING ASSEMBLY 18-MAN-02 MANUAL (NOT SHOWN) 19-408-00 DRIVE, 110V METABO 21-014-00 NAME PLATE 90-049-01 SCREW, 3/16 U-DRIVE 90-800-19 WRENCH, 5/32 HEX LONG ARM (NOT SHOWN) 90-800-39 WRENCH, 1/8 HEX TEE HANDLE (NOT SHOWN) Part No. 18-MAN-02, Rev. 3-1013 E.H. Wachs...
- Página 17 FSE HOUSING ASSEMBLY 18-MAN-02 MANUAL (NOT SHOWN) 19-409-00 DRIVE, 220V METABO 21-014-00 NAME PLATE 90-049-01 SCREW, 3/16 U-DRIVE 90-800-19 WRENCH, 5/32 HEX LONG ARM (NOT SHOWN) 90-800-39 WRENCH, 1/8 HEX TEE HANDLE (NOT SHOWN) E.H. Wachs Part No. 18-MAN-02, Rev. 3-1013...
- Página 18 FSE HOUSING ASSEMBLY 18-408-00 DRIVE, CORDLESS 110V METABO 18-MAN-02 MANUAL (NOT SHOWN) 21-014-00 NAME PLATE 90-049-01 SCREW, 3/16 U-DRIVE 90-800-19 WRENCH, 5/32 HEX LONG ARM (NOT SHOWN) 90-800-39 WRENCH, 1/8 HEX TEE HANDLE (NOT SHOWN) Part No. 18-MAN-02, Rev. 3-1013 E.H. Wachs...
- Página 19 FSE Housing Assembly, 18-302-00 E.H. Wachs Part No. 18-MAN-02, Rev. 3-1013...
- Página 20 DESCRIPTION 18-035-00 BASE, STAND 18-036-00 SUPPORT, STAND 90-093-13 FHCS, 1/2-13 X 2-1/2 110 V Cordless Electric Drive, 18-408-00 ITEM PART NUMBER QTY. DESCRIPTION 18-059-01 18V CORDLESS MOTOR (110V, 2-BAT. PACKS) 19-034-01 ADAPTER, MOTOR Part No. 18-MAN-02, Rev. 3-1013 E.H. Wachs...
- Página 21 Shoe Set, 18-403-XX E.H. Wachs Part No. 18-MAN-02, Rev. 3-1013...
- Página 22 ITEM PART NUMBER QTY. DESCRIPTION 18-403-02 SHOE SET .250 DIA. [6.35mm] 18-403-04 SHOE SET .375 DIA. [9.53mm] 18-403-06 SHOE SET .500 DIA. [12.70mm] 18-403-10 SHOE SET .750 DIA. [19.05mm] 18-403-14 SHOE SET 1.000 DIA. [25.40mm] Part No. 18-MAN-02, Rev. 3-1013 E.H. Wachs...
-
Página 23: Section X. Ordering Information
FSE FITTING SQUARING MACHINE FSE ORDERING INFORMA TION SECTION X To place an order or to get more detailed information on any E.H. Wachs products, call us at: 1-800-323-8185. ORDERING REPLACEMENT PARTS Please use parts list provided in manual. Have part description and part number of required replacement part or parts to help expedite order and insure proper parts are being ordered. - Página 24 600 Knightsbridge Parkway • Lincolnshire, IL 60069 847-537-8800 • www.ehwachs.com...