Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Control Lock:
The user interface can be locked to avoid unintentional
changes from things like cleaning. To lock the appliance,
push and hold the "LOCK" icon for 5-seconds. The "LOCK"
icon will flash 3 times, then change to steady back-lit. To
unlock the user interface, press and hold the "LOCK" icon
for 5-seconds, and the back-light will turn off.
NOTE
The "LOCK" icon is the only active key in this mode.
If other icons are pressed while in the lock mode the
"LOCK" icon will flash 3 times, and an audible tone
will sound, to remind the user the appliance is in the
lock mode.
Door ajar alarm:
If the door is open, or not closed properly for 5
minutes the "DOOR" indicator will illuminate and
flash and an audible tone will sound. The audible
alarm can be muted by pressing the "Lock" keypad.
This alarm condition can be reset by closing the
door or momentarily pressing the "ON/OFF" icon,
(i.e.-if you are cleaning the storage compartment, etc.). The
alarm will recur in 5 minutes if the alarm condition persists.
Delay start/Vacation mode:
Your ice machine is equipped with a delay start function.
This feature can be used to temporarily shut the appliance
off for 1, 4, 6, or 8 hours or days. Upon completion of the
selected delay period, the appliance will resume operation.
This is ideal for temporarily stopping ice machine noises or
to save water and electricity if you are away from home but
want fresh ice upon your return.
Error codes:
The ice machine is monitored continuously. Any OPEN or
SHORTED circuit condition with a temperature sensor or
miscommunications between the control and user interface
will initiate an ERROR CODE as listed below:
Error
"OFF" will flash continuously in 1
Bin Sensor error
second intervals in the display. No
audible alarm will sound.
"ICE" will flash continuously in
System Sensor error
the display. No audible alarm will
Continual flashing of all indicators
Communication error
USING YOUR ELECTRONIC CONTROL
DOOR
Displayed Code
Failed temperature sensor. Machine operation will imme-
Failed condenser temperature sensor. Machine opera-
tion will continue but ice production cycle will not adapt to
sound.
varying ambient conditions, so ice quality may vary.
Loss of communication between the main board and the
on the display.
To enter the delay start mode, press the "CLOCK"
icon while the appliance is in "ICE" mode. This will
delay the next harvest by the time displayed. Each
additional press of the "CLOCK" icon will add time,
from 1, 4, 6, or 8 hours, to 1, 4, 6, or 8
days. The next press after 8 days will
leave delay set mode. After the desired
time has been selected, press the "ON/OFF" icon
for 2 seconds to accept, your unit will shut off and a
clock icon and your selected time will be displayed.
When the selected time has elapsed, normal ice pro-
duction will resume.
To cancel the delayed start, press and
hold the "ON/OFF" icon until the appli-
ance enters OFF, then press and hold
the "ON/OFF" icon again until the appli-
ance enters "ICE" mode.
Options menu:
Normal and ECO mode:
Your ice machine comes with an optional "ECO" mode.
This new feature allows you to tailor ice production to a
conservative rate, saving approximately 25% energy and
30% water from routine operation. While in this mode ice
production will slow and the appliance will use less water
and electricity. "ECO" mode should only be initi-
ated after there is a full bin of ice. To enter "ECO"
mode do the following:
•
Press the "MENU" icon twice and the green
"ECO" will flash.
•
Press and hold the "ON/OFF" icon until the
green "ECO" stops flashing and remains illumi-
nated.
•
To return to the standard operating rate press the
"MENU" icon twice, the ECO will turn off and
the "ICE" will be flashing. Press and hold the
"ON/OFF" icon until the "ICE" stops flashing
and remains illuminated.
Error Codes
Error Description
diately enter an OFF state.
user interface.
15
hours
days
1
4
6
8
OFF
ICE
ECO
ICE
Action to Take
Call service to have the
temperature sensor replaced.
Call service to have the
temperature sensor replaced.
Call service to have a
diagnostic check.
Capítulos
Tabla de contenido
