Idiomas disponibles
Idiomas disponibles
Produktgruppe 512
7 von 36
Note
The kit, Mat. no. 09079450, for PW 6107, PW 6137, PW 6167 and PW 6207 contains the following:
1 electronic module EZL 235, module 2 (liquid dispensing 7 - 12)
4 spacers (for electronic module EZL 235 fastening)
1 coding plug MFM 2-5 (module 2 EZL 235 - Plug connector ST3), PIN 2-5
1 wiring harness 20X-41X (module 2 EZL 235 - Plug connector ST10 / modul 1 EZL 235 - Plug connector ST9), plug housing,
3-pole, 500 mm
1 wiring harness N1Q_ST112, N1Q_ST11 (module 2 EZL 235 - Plug connector ST111 / module 1 EZL 235 - Plug connector
ST112), plug housing, 4-pole, 350 mm
3 connection wires, black 0.75 x 90
1 screw connector strip, 6-pole, blue
1 screw connector strip, 7-pole, green
1 terminal strip 1X3-4, orange
1 terminal strip 2X3-4, grey
1 terminal strip 3X3-4, blue
1 terminal strip 4X3-4, green/yellow
1 accessory module
1 wiring diagram PW 6107 - PW 6207 module 2, Mat. no. 09021420
Fitting instructions - Module 2, liquid dispensing 7 - 12, Mat. no. 09087211.
Note
The kit, Mat. no. 09885130, for PW 6107, PW 6137, PW 6167 and PW 6207 contains the following:
1 electronic module EZL 235, module 2 (liquid dispensing 7 - 12)
4 spacers (for electronic module EZL 235 fastening)
1 coding plug MFM 2-5, AWG (module 2 EZL 235 - Plug connector ST3), PIN 2-5
1 wiring harness 20X-41X, SIF18 (module 2 EZL 235 - Plug connector ST10 / module 1 EZL 235 - Plug connector ST9), plug
housing, 3-pole, 500 mm
1 wiring harness N1L_ST11BN1Q_ST11AWG (module 2 EZL 235 - Plug connector ST111 / module 1 EZL 235 - Plug connector
ST112), plug housing, 4-pole, 350 mm
3 connection wires, brown AWG 20 x 90
1 screw connector strip, 6-pole, blue
1 screw connector strip, 7-pole, green
1 terminal strip 1X3-4, orange
1 terminal strip 2X3-4, grey
1 terminal strip 3X3-4, blue
1 terminal strip 4X3-4, green/yellow
1 accessory module
1 wiring diagram PW 6107 - PW 6207 module 2, Mat. no. 09021420
Fitting instructions - Module 2, liquid dispensing 7 - 12, Mat. no. 09087211.
List of illustrations:
Fig. 1: Fitting electronic module EZL 235
Fig. 2: Connecting electronic module EZL 235, module 2, liquid dispensing 7 - 12
Fig. 3: Fitting cable throughfeed on connection strip
Disconnect the machine from the gas (if applicable) and electric mains and ensure utilities cannot be switched on again in error.
Remove 1 screw from each side of the lid at the top of the machine.
Lift the front of the lid slightly, slide it to the rear and thus release the centring cones at the rear of the lid from the connection strip.
Remove the lid upwards.
Fit the electronic module EZL 235 with 4 spacers in the pre-punched holes of the side component support, Fig. 1, Pos. 1, Pos. 2.
Fit the terminal strips in the pre-punched holes of the component support, Fig. 1, Pos. 3.
06.02.2014
Diese Unterlagen dürfen ohne unsere Genehmigung weder vervielfältigt noch Dritten zugänglich gemacht werden. Eigentumsrechte vorbehalten.
Umbau- und Montageanweisung
M.-Nr. 09087211
