Replacing Blades (16:P); Spare Parts - Stiga PARK 110 COMBI PRO Instrucciones De Uso

8. Grip the front edge of the deck and lift up. Lift
until the deck is completely vertical and rest the
rear edge on the ground. See fig. 14.
9. Lower the deck to the ground in reverse order
after the corrective actions have been carried
out. Reset the deck according to 3.1.
5.3.2 Machines with quick connections
Example of quick connections, see fig. 8.
1. Activate the parking brake.
2. If the deck has electrical cutting height adjust-
ment, disconnect the cable from the machine.
See fig. 13.
3. Set the maximum cutting height.
4. See fig. 2. Detach the rear section of the deck on
the right and left-hand side as follows:
A. Lift up the left-hand rear section of the deck
slightly to reduce the load from the cotter
pin.
B. Remove pins and washer.
C.Remove the right-hand cotter pin and washer
in the same way.
5. Set the quick connections in their rear positions.
See their supplied separate instruction.
6. Release the belt tension as follows.
Park 4WD:
Grip the belt tensioner's lever with your left
hand. Pull the lever and remove the tensioner
with your right hand. See fig. 9.
Park 2WD:
Remove the tensioner from the belt. See fig. 10.
7. Force the belt off the machine's pulley.
Check that the quick connections are in
their front positions before raising the
deck. Otherwise there is a risk of crush-
ing injuries.
8. Set the quick connections to their front posi-
tions, see separate instructions.
9. Grip the front edge of the deck and lift up. Lift
until the deck is completely vertical and rest the rear edge on the ground. See fig. 20.
10.Lower the deck to the ground in reverse order
after the corrective actions have been carried
out. Reset the deck according to 3.2.
5.4 CLEANING
The underside of the deck must be cleaned after
each use.
Set the deck in washing position.
Clean the underside of the deck carefully. Use wa-
ter and a brush.
When the surfaces are completely dry and clean,
touch up the paintwork. Use durable yellow paint
intended for metal outdoors.
ENGLISH
5.5 WHEELS
110/125 Combi Pro is fitted with two lubricating
cups (15:O) for the vertical shafts.
The grease nipples must be lubricated with univer-
sal grease after 50 hours of operation.

5.6 REPLACING BLADES (16:P)

Wear protective gloves when changing
blade(s) to avoid cutting yourself.
Check that the blades are always sharp. This pro-
duces the best cutting results.
Always check the blade(s) after a collision. If the
blade system has been damaged, defective parts
should be replaced.
Always use genuine spare parts. Non-
genuine spare parts can entail a risk of
injury, even if they fit the machine.
The full blade is replaced when the edges are worn.
Install the new blade with the punched text facing
down.
Tightening torque: 45 Nm.
5.7 WEAR PROTECTION
There are two wear protection devices on the un-
derside of the cutting deck to protect it. These can
be replaced if necessary.

6 SPARE PARTS

STIGA genuine spare parts and accessories are de-
signed specifically for STIGA machines. Please
note that 'non-genuine' spare parts and accessories
have not been checked or approved by STIGA:
The use of such parts and accessories
can affect the function and safety of the
machine. STIGA accepts no responsi-
bility for damage or injuries caused by
such products.
7 DESIGN REGISTRATION
This product or parts thereof is covered by the fol-
lowing design registration:
Sweden: 66 166
Germany: 499 11 740.9
France: 577 251-253, 577 439-443
USA: 435 564
GGP reserves the right to make alterations to the
product without prior notification.
EN
29