Maytag MDB-9 Guía De Uso Y Cuidado página 15

PROBLEM
Display time drops
or increases
(select models)
Glasses are cloudy/
spotted
Food soil remains
on dishes
Items washed in the
dishwasher or the
dishwasher tub itself
are stained/discolored
Items not properly
dried/moisture is
present on the
dishwasher interior
after the dry cycle
Dishware is chipped
Sanitized light does not
illuminate at the end of
the cycle (select
models)
Dishwasher door will
not close
*Brand names are trademarks of the respective manufacturer.
SOLUTION
• This is normal when the Auto Clean (select models) or Normal Wash cycle is selected and
the dishwasher decides to skip or add a drain and refill.
• Select Hi Temp Wash option.
• Check water temperature. Incoming water should be 120° F (49° C).
• Always use a rinse aid.
• Confirm that the cloudiness is removable by soaking the item in white vinegar for
approximately 5 minutes. If removed, the problem is due to hard water. Adjust detergent
amount being used to match water hardness (pg. 7). Be sure detergent is fresh, stored
properly and is a high quality brand.
• If cloudiness is not removable, it is etching. This is an erosion of the surface of the glassware
and can be caused by water that is too hot, from using too much detergent or by
prewashing. Detergent needs food soil to act upon. If etching has occurred, the glassware is
permanently damaged. To prevent further etching, adjust the detergent amount to match
the water hardness, stop prewashing, and use water heating options only when incoming
water temperature is below 120° F (49° C).
• Check water temperature. Incoming water should be 120° F (49° C).
• Run hot water at the sink before starting the dishwasher.
• Check water hardness and adjust detergent amount accordingly (pg. 7).
• Use fresh detergent stored in a cool dry place.
• Select proper cycle for the soil level (pg. 8).
• Select proper option, ToughScrub
• Make sure the upper rack wash arm connector is correctly aligned in one of the water inlet
holes (pg. 6).
• Load items so they do not block the wash arms (pgs. 3-6).
• Load the utensil basket with knife handles up and spoon and fork handles down.
• Do not place glasses over tines.
• Before loading, scrape off burnt on foods and wipe the starchy film from utensils used with
pasta, rice and oatmeal. These soils require more energy than the rest of the load to clean.
• Aluminum utensils or pans can leave marks when they rub against other items. Leave a
slight space between items.
• Iron deposits in the water can leave a yellow, brown or orange film on dishes or the
dishwasher tub. A rust filter may be needed. Check with a water treatment company.
• Separate silver or silver-plated silverware from stainless steel. These metals can be damaged
by contact with each other during washing.
• Color from tomato sauces may adhere to the interior parts of the dishwasher (pg. 12). If light
staining has occurred, leave the door open to oxidize the stain away. Use a dishwasher
detergent that contains chlorine to better fight staining.
• Certain dishwasher detergents may stain silver. Try another brand of detergent.
• Be sure Heated Dry is selected.
• Water droplets may form on the inner door as part of the drying process.
• Use a rinse aid separate from the detergent like Jet Dry* or Cascade Rinse Aid* regularly, to
improve drying. Turn the rinse aid selector toward the MAX setting.
• Check water temperature. Incoming water should be 120° F (49° C).
• Select Sanitize option.
• Increase detergent amount to match water hardness (pg. 7).
• Load properly. (pgs. 3-6)
• Plastic and items with non-stick surfaces are difficult to dry because they have a porous
surface which tends to collect water droplets. Towel drying may be necessary.
• Glasses and cups with concave bottoms hold water and require towel drying. Locate these
items on the more slanted side of the rack for improved results.
• Load dishes according to instructions so they do not strike each other (pgs. 3-6).
• Washing fine antique china/crystal in the dishwasher is not recommended.
• Do not load glasses over the tines.
• Do not overload.
• Sanitize was not selected.
• Sanitization can only be achieved with the Auto Clean (select models), Heavy Wash, Normal
Wash or Light Wash cycles.
• Sanitization may not be achieved if there is an interruption of the cycle, power failure or if
incoming water temperature is below 120° F (49° C).
• Be sure adjustable racks (select models) are properly adjusted to upper or lower position
(pg. 6).
TM , ToughScrub TM Plus or Hi Temp Wash (select models).
14