Tabla de contenido
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
Note: the burner may be noisy when initially turned on. To eliminate excessive noise from
the burner, turn the control knob to the pilot position. Then, turn the knob to the level of heat
desired.
When heater is ON:
Emitter screen will become bright red due to intense
heat. The color is more visible at night.
Burner will display tongues of blue and yellow flame.
These flames should not be yellow or produce thick
black smoke, indicating an obstruction of airflow through
the burners. The flame should be blue with straight
yellow tops.
If excessive yellow flame is detected, turn off heater and
visit www.bluerhino.com or call 1.800.762.1142.
Re-lighting
Note: For your safety, control knob cannot be turned "OFF" without first depressing control
knob in PILOT position and then rotating it to "OFF".
1. Turn control knob to "OFF".
2. Wait at least 5 minutes, to let gas dissipate, before attempting to relight pilot.
3. Repeat the "Lighting" steps.
Shut Down
1. Turn control knob clockwise to pilot. (Normally, burner will make a slight popping sound when
extinguished.) Burner will extinguish but pilot will remain "ON".
2. To extinguish pilot, depress control knob and continue to turn it clockwise to "OFF".
3. Turn tank valve clockwise to "OFF" and disconnect regulator when heater is not in use.
Note: After use, some discoloration of the emitter screen is normal.
Cleaning and Care
CAUTION: All cleaning and maintenance should be done when patio
heater is cool and with the fuel supply disconnected.
CAUTION: DO NOT clean any patio heater part in a self cleaning oven.
The extreme heat will damage the finish.
Notices
1. Abrasive cleaners will damage this product.
2. Never use oven cleaner to clean any part of heater.
3. Do not clean any heater part in a self cleaning oven. The extreme heat will damage the
finish.
4. More frequent cleaning may be required as necessary. It is imperative that control
compartment, burners and circulating air passageways of the heater be kept clean.
5. Spiders and insects can create a dangerous condition that may damage heater or
make it unsafe. Keep burner area clean of all spiders, webs, or insects. Clean burner
holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller
particles.
6. Inspect heater before each use.
7. Have heater inspected annually and repairs should be made by a qualified service
person.
8. Check heater immediately if any of the following conditions exist:
a. The smell of gas in conjunction with extreme yellow tipping of burner flames.
b. Heater does not reach proper temperature.
Note: At temperatures less than 40ºF, heat output will be reduced.
c. Heater's glow is excessively uneven
d. Burner makes popping noises during use.
Note: A slight pop is normal when burner is extinguished.
9. Carbon deposits may create a fire hazard. Keep dome and emitter clean at all times.
10. Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water.
11. Do not paint engine, engine access panel or dome.
12. This heater should be thoroughly cleaned on a regular basis.
13. After a period of storage and/or nonuse, check for leaks, burner obstructions and
inspect for any abrasion, wear, cuts to the hose.
Cleaning Surfaces
1. Wipe surfaces clean with mild dishwashing detergent or baking soda.
2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush.
3. Rinse clean with water.
Note: While cleaning your unit, be sure to keep the area around the burner and pilot assembly
dry at all times. Do not submerge the control valve assembly. If the gas control is submerged in
water, do NOT use it. It must be replaced.
Cleaning and Care (continued)
Maintenance
To enjoy years of outstanding performance from your heater, make sure you perform the
following maintenance activities on a regular basis:
1. Keep exterior surfaces clean.
2. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean.
Signs of possible blockage include:
Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than
normal. Frequently check for corroded areas and repair them promptly.
Proper flame height.
TIP: Use high-quality automobile wax to help maintain the appearance of your heater. Apply to
exterior surfaces from the pole down. Do not apply to emitter screen or domes.
Storage
Between uses:
1. Turn Control Knob OFF.
2. Disconnect LP source.
3. Store heater upright in an area sheltered from direct contact with inclement weather (such as
rain, sleet, hail, snow, dust and debris).
4. If desired, cover heater to protect exterior surfaces and to help prevent build up in air
passages.
Note: Wait until heater is cool before covering.
During periods of extended inactivity or when transporting:
1. Turn Control Knob "OFF".
2. Disconnect LP source and move to a secure, well-ventilated location outdoors.
3. Store heater upright in an area sheltered from direct contact with inclement weather (such as
rain, sleet, hail, snow, dust and debris).
4. If desired, cover heater to protect exterior surfaces and to help prevent build up in air
passages.
5. Never leave LP tank exposed to direct sunlight or excessive heat.
Note: Wait until heater is cool before covering.
Product Registration
For faster warranty service, please register your product immediately at www.bluerhino.com or
call 1.800.762.1142.
Gas odor with extreme yellow tipping of flame.
Heater does NOT reach the desired temperature.
Heater glow is excessively uneven.
Heater makes popping noises.
page no.
9
Tabla de contenido
