Bosch Professional GSH 501 Manual Original página 12

Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Changing the Tool
With the SDS-max tool holder, you can change the applica-
tion tool simply and easily without additional aids.
The dust protection cap (1) largely prevents the penetration
of drilling dust into the tool holder during operation. When
inserting the tool, make sure that the dust protection cap (1)
does not become damaged.
Replace a damaged dust protection cap immediately.
u
It is recommended that you have use an after-sales
service for this.
Inserting the application tool (see figure A)
– Clean and lightly grease the shank of the application tool.
– Push the locking sleeve (2) back and insert the applica-
tion tool by turning it into the tool holder. Release the
locking sleeve (2) to lock the application tool.
– Check the latching by pulling the tool.
Removing the application tool (see figure B)
– Push the locking sleeve (2) back and remove the applica-
tion tool.
Auxiliary Handle
Do not operate your power tool without the auxiliary
u
handle (6).
You can swivel the auxiliary handle (6) to any angle for a safe
work posture that minimises fatigue.
– Turn the lower gripping end of the auxiliary handle (6) an-
ticlockwise and swivel the auxiliary handle (6) into the re-
quired position. Then, turn the lower gripping end of the
auxiliary handle (6) clockwise to retighten.
Operation
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Starting Operation
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Bosch Power Tools
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Switching On and Off
– To start the power tool, press and hold the on/off switch
(5).
– Press the lock-on button (4) to lock the on/off switch (5)
in this position.
– To switch off the power tool, release the on/off switch
(5); or, if the switch is locked with the lock-on button (4),
briefly press the on/off switch (5) and then release it.
At low temperatures, the power tool will take a certain
amount of time to reach its full impact performance. You can
shorten this warm-up time by tapping the power tool's inser-
ted application tool on the ground once.
Changing the Chiselling Position (Vario-Lock) (see
figure )
You can lock the chisel in 12 different positions, allowing
you to select the optimum working position for each task.
Insert the chisel into the tool holder and turn the chisel to the
required position.
Working Advice
Sharpening the chiselling tools (see figure C)
Only sharp chiselling tools will produce good results, there-
fore sharpen your chiselling tools in good time before use.
This will ensure a long service life for the tools and good
work results.
Re-sharpening
Grind chiselling tools against sanding discs, e.g. aluminium
oxide, under a steady stream of water. Make sure that the
cutting edges show no annealing colours; this will impair the
hardness of the chiselling tools.
To forge a chisel, heat it to 850–1050 °C (pale red to yel-
low).
To harden a chisel, heat it to approx. 900 °C and quench in
oil. Then, leave it in an oven for approx. one hour at 320 °C
(annealing colour: pale blue).
Maintenance and Service
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Автотовары «130»
English | 11
Turn the chisel adjustment
switch (3) to the Changing
the Chiselling Position
(Vario-Lock) position.
Turn the chisel adjustment
switch (3) to the Chiselling
position and turn the chisel
until it audibly clicks into
place.
1 609 92A 3BN | (08.04.2021)