Tabla de contenido
Idiomas disponibles
Idiomas disponibles
When the refrigerator is placed on such flooring materials as carpet, straw mat, polyvinyl chloride, the solid backing plates
should be applied underneath the refrigerator, so as to prevent color change due to heat dissipation.
Unobstructed ventilation shall be maintained around the appliance or in an embedded structure.
Preparations for use
5.
Standing time
After the refrigerator is properly installed and well cleaned, do not switch it on immediately. Make sure to energize the
refrigerator after more than 1 hour of standing, so as to ensure its normal operation.
6.
Cleaning
Confirm the accessory parts inside the refrigerator and wipe the inside with a soft cloth.
7.
Power-on
Insert the plug into the solid socket to start the compressor. After 1 hour, open the freezer door, if the temperature inside
the freezer compartment drops obviously, it indicates the refrigeration system is working normally.
8.
Storage of food
After the refrigerator runs for a period of time, the internal temperature of the refrigerator will be automatically controlled
according to the user's temperature setting. After the refrigerator is fully cooled, put in foods, which usually need 2~3
hours to be fully cooled. In summer, when the temperature is high, it takes more than 4 hours for the foods to be fully
cooled (Try to open the refrigerator door as less as possible before the internal temperature cools down).
If the refrigerator is installed in the moisture place, make sure to check whether the ground wire and leakage circuit
breaker are normal. If vibration noises are produced due to the refrigerator contacting the wall or if the wall gets blackened
by air convection around the compressor, move the refrigerator away from the wall. Setting up the refrigerator may cause
jamming noise or image chaos to the mobile phone, fixed-line telephone, radio receiver, television set surrounding it, so
try to keep the refrigerator as far away as possible in such case.
XIV.
Functions
When the refrigerator system is connected to power supply for the first time, all icons on the display
panel gets illuminated for 2s, and the system runs in the Smart mode by default. When all the doors are
close, the display gets extinguished automatically if no key operation within 3 minutes. When the
display is off, it will light up if any door is opened or any key is pressed.
The following key operations are valid only when the keys are unlocked and gets illuminated on the
display.
★Temp. setting
1）Fridge temperature setting
Press the Temp. Zone key to select the fridge zone, with the corresponding icon flickering, and then
press the Temp. key to adjust the temperature, finally press the OK/Lock or wait for 5s to validate the
above temperature setting.
The fridge temperature setting cycles as following:
5→6→7→8→OFF→2→3→4→5；
OFF refers to Fridge Off, and when OFF takes effect, the fridge will stop cooling.
Take foods out of the fridge compartment before setting this function.
2）Freezer temperature setting
Press the Temp. Zone key to select the freezer zone, with the corresponding icon flickering, and then
press the Temp. key to adjust the temperature, finally press the OK/Lock or wait for 5s to validate the
above temperature setting.
The freezer temperature setting cycles as following:
-18→-17→-16→-24→-23→-22→-21→-20→-19→-18
★ Smart
1）When the Smart function is enabled, the temperature of the fresh food compartment is controlled at 4 ℃, and that of
the freezer compartment at - 18 ℃, so that foods can be stored in the best condition while the refrigerator is running more
efficiently and with better performance.
Under the Smart mode, the fresh food compartment temperature and the freezer compartment temperature are
subject to no change.
2）Enabling the Smart function
Press the Function key to select Smart until the corresponding icon gets flickering, and then press the OK/Lock key
within 5s for confirmation. If the OK is not pressed within 5s, the setting will be invalidated.
3）Exiting the Smart function
Under the Smart mode, press the Function key to select Smart until the corresponding gets flickering, and then press
the OK/Lock key for confirmation. The Smart function will get exited.
When the Vacation or Fast Freeze or Fast Cool function is enabled, the Smart function will be disabled automatically.
★ Fast Cooling
1) When this function is enabled, the fridge temperature is automatically set at 2℃, with the temperature reduced in the
rapid manner, so that foods can be kept in fresh condition with their nutrition not lost.
Tabla de contenido
