Overheating Protection; Initial Operation; Technical Data; Guarantee - Clatronic KH 3077 Instrucciones De Servicio/Garantía

3. Attach the two angle brackets to the wall using the 35 mm
screws and the rawlplugs.
4. Insert the housing into the brackets. Please note illustration
2b, which shows the back of the device.
5. Mark the holes for the spacers on the wall.
6. After you have drilled these holes you can now also screw
these brackets to the wall.

Initial Operation

• Only connect the machine to a properly installed safety
socket, 230 V/50 Hz.
• Make sure that the degree of protection of the socket to
which the device is connected is of at least 10 ampere!
• Place the device on any heat-resistant fl at surface. Ensure
that air can enter and leave unhindered.
• The distance from the air outlet grille to the nearest wall
should be at least 1 m.
Function Switch
The heating power is determined by the various levels. The
radiator offers 3 heating levels for ideal comfort:
When operating switches I and II are turned on the control lamp
in the switch lights up (see illustration 4).
Operational switch I alone is on
Operational switch II alone is on
Operational switches I + II are on
The control lamp lights up when the device is heating up.
Thermostat
You can set the room temperature with the temperature control.
Lowest level
Controlling Room Temperature
• Turn the thermostat control knob to the highest level. The
LED will light up.
• Once the desired room temperature is reached, turn the
thermostat control knob slowly back until the device shuts
off (control lamp goes off).
• The thermostat maintains the set room temperature by
switching the device on and off.
Switching off
Turn the thermostat to MIN and move the off switch to the
•
off position in order to turn the device off.
• Remove the plug from the socket after use.
26
05-KH 3077 26
• The device is equipped with an overheating protection that
switches the device automatically off in case of overheating.
Shift the function switch to „0" position and pull out plug out
of the socket. Let the device cool down for about
10 minutes before using it again.
• Is the device overheating? Check whether the air intake or
outlet of the heater is blocked. If so, the blockage should be
removed.
• Should the overheating protection shut the device off again
shortly after, there is probably a defect. Switch off the device
again and pull out the plug.
• Before cleaning the machine you should always remove the
mains lead and wait until the machine has cooled down. The
machine should only be cleaned with a slightly damp cloth.
• Do not use any strong detergents or solvents for cleaning.
Model: ..............................................................................KH 3077
Power supply:............................................................230 V, 50 Hz
Power consumption:..........................................................2000 W
= 750 W
= 1250 W
Protection class:........................................................................... Ι
= 2000 W
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
The device supplied by our Company is covered by a 24 month
guarantee starting on the date of purchase (receipt).
Highest level
During the life of the guarantee any fault of the device or its
accessories ascribable to material or manufacturing defects will
be eliminated free of charge by repairing or, at our discretion, by
replacing it. The guarantee services do not entail an extension
of the life of the guarantee nor do they give rise to any right to a
new guarantee!
Proof of the guarantee is provided by the proof of purchase.
Without proof of purchase no free replacement or repair will be
carried out.
If you wish to make a claim under the guarantee please return
the entire machine in the original packaging to your dealer
together with the receipt.
Defects to consumables or parts subject to wearing (e.g. motor
pistons, kneading blades, drive shafts, spare remote control,
spare toothbrushes, saw blades, etc.) as well as cleaning,
maintenance or the replacement of said parts are not covered by
the guarantee and hence are to be paid!
The guarantee lapses in case of unauthorized tampering.

Overheating Protection

Cleaning

Technical Data

Guarantee

27.04.2006, 14:54:42 Uhr