Tabla de contenido
Idiomas disponibles
Idiomas disponibles
•
With the extension tube
13
. (Fig. I)
•
With an accesssory tool
12
Switching ON and OFF (Fig. F)
•
To switch ON, press the ON/OFF button
•
For increased power, slide the variable power
switch
2
forward.
nOTE: The state of charge indicator LEDs will illuminate
while the vacuum is ON.
•
To switch OFF, press the ON/OFF button
second time.
•
Return the product to the charger immediately after use
so that it will be ready and fully charged for the next
use. Ensure that the product is fully engaged with the
charger plug.
Switching the Floor Brush OFF and ON (Fig. A)
•
To switch the floor brush OFF, press the Floor brush ON/
OFF button
4
.
•
To switch the floor brush ON, press the floor brush ON/
OFF button
4
a second time.
nOTE: The LED worklights
the floor brush is switched ON.
Using an Accessory Tool (Fig. A, K)
Your vacuum may come with some of the following tools.
Small crevice tool.
‑
‑
6" Brush tool.
•
The accessories
12
,
13
can be fitted either directly to the
extension tube
6
or to the vacuum inlet
Fig. A, K.
•
Align the top of the accessories
inlet
5
or extension tube
locks into position as shown in Fig. A, K.
MAINTENANCE
WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Cleaning
WARNING:
out of all air vents with clean, dry air at least once
a week. To minimize the risk of eye injury, always
wear ANSI Z87.1 approved eye protection when
performing this procedure.
WARNING:
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
6
and an accesssory tool
12
,
13
. (Fig. J)
1
.
1
a
11
will illuminate whenever
5
as shown in
12
,
13
with the vacuum
6
and push into place so it
To reduce the risk of serious
Blow dirt and dust
Never use solvents or other
,
inside the tool; never immerse any part of the tool into
a liquid.
Cleaning and Emptying the Vacuum
WARNING:
Never use the vac without its filter.
nOTE: The filter is re-usable, do not confuse it with a
disposable dust bag, and do not throw it away when the
product is emptied. We recommend that you replace the
filter every 6–9 months depending on frequency of use.
There are two methods of cleaning the canister, a quick
empty method and a thorough clean method.
To Empty the Dust Canister (Fig. l, M)
•
Lift and remove the lift away dust canister
chassis
16
as shown in Figure L.
•
Place the dust canister over a trash bin and press the dust
canister lid release button
as shown in Figure M.
•
Close the dust canister lid
into position.
•
Install the lift away dust canister
chassis
16
.
Removing Pre-filter (Fig. l, M, n)
•
Lift and remove the lift away dust canister
chassis
16
as shown in Figure L.
•
Place the dust canister over a trash bin and press the dust
canister lid release button
as shown in Figure M.
•
Use your index finger and thumb to pinch the pre-filter
pull the pre-filter
19
in Fig. N.
nOTE: The filter housing fits snuggly in the dust canister
and may be difficult to remove at first.
•
Empty the dust canister into a trash bin.
nOTE: It is recommended that you agitate the filter when
the pre-filter
19
is removed. See Filter Agitator section
for instructions.
•
Install the pre-filter
the dust canister tab
as shown in Fig. N.
•
Install the dust canister onto the vacuum, until it clicks
firmly into position.
Filter Agitator (Fig. l, M, n)
•
Lift and remove the lift away dust canister
chassis
16
as shown in Figure L.
•
Place the dust canister over a trash bin and press the dust
canister lid release button
as shown in Figure M.
•
Use your index finger and thumb to pinch the pre-
filter
, pull the pre-filter
19
as shown in Fig. N.
nOTE: The filter housing fits snuggly in the dust canister
and may be difficult to remove at first.
•
Rotate the filter agitator wheel
over a trash bin to remove excessive dust from the filter.
English
Projectile/Respiratory Hazard:
9
from the
17
to empty the dust canister
18
, until it clicks firmly
9
back onto the
9
from the
17
to empty the dust canister
from the dust canister
9
as shown
19
into the dust canister
9
20
aligns with the pre-filter slot
9
from the
17
to empty the dust canister
from the dust canister
19
8
five to ten revolutions
19
,
ensuring
21
9
9
Tabla de contenido
