Know Your Product; Operation - RS Components 754-1915 Instrucciones De Uso

ReAD All Of tHe INstRUCtIONs IN tHe CHARG-
eR seCtION Of tHIs mANUAl befORe AttemPt-
ING tO CHARGe tHe bAtteRy PACK fOR yOUR
tOOl.
▪ Always use correct RS battery pack (the one supplied
with tool or a replacement pack exactly like it). Never
install any other battery pack. It will ruin your tool and
may create a hazardous condition.
▪ Charge battery packs only in RS chargers.
▪ Use an environmentally safe disposal unit at a munici-
pal waste disposal centre to dispose of a damaged or
worn out battery.
fIttING AND RemOvING tHe
bAtteRy PACK
To remove the battery from the machine: press the bat-
tery release buttons (4) and take the battery out of the
tool.
WARNING: Always set the forward/reverse
switch (3) in central position before any work on the
machine e. g. fitting and removing a battery, changing
the bit,, transport, maintenance and storage.
To install the battery: Insert the charged battery into the
opening at the base of the power tool until the battery is
securely latched with a click.
bAtteRy CHARGING
▪ Insert the plug of the charger in the socket. The green
LED on the charging indicator (10) will start to glow
thus indicating that the charger is in standby state.
▪ Insert the battery (5) in the charger socket (9) consid-
ering the polarity. (Fig. 1)
▪ A new battery will work properly after five cycles of
charging and discharging. Charge and discharge a
battery, which is not used for a long time, for two to
three times to function well.
▪ When the battery working time is remarkably short de-
spite full charging, the life of the battery may be over.
Replace the battery immediately.
WARNING: The battery will be fully charged
after approximately 30 min, remove it from the charger
after this time.
Charging indication:
▪ The green LED starts to glow upon plugging the
charger in the mains.
▪ The green LED ceases to glow and the red LED lights
up after the battery has been placed in the charger,
thus indicating the beginning of the charging process.
During the charging process the charger and battery
might become warm. This is a normal condition, and
does not indicate a problem.
▪ After completion of charging which takes approxi-
mately 30 min, the red LED ceases to glow and the
green LED lights up.
Original instructions
RS-754-1915-pages-BR2 7.2Li.indd 7
The charger features thermal overload protection for the
battery. Nevertheless we recommend withdrawing the
battery from the charger upon expiring of the charging
time. You may use additionally an electric timer in order
to control the charging time.
tO ObtAIN tHe best lIfe fOR tHe bAtteRy
▪ When battery is not in use, keep it away from other
metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make
a connection from one terminal to another. Shorting
the battery terminals together may cause fire or ex-
plosion.
▪ Always unplug the charger when not in use and store
in a dry secure place.
▪ Do not charge battery packs and do not store the
charger in premises where the temperature may drop
under 0ºC or exceed +40ºC.
VII - Know your product
Before using the power tool, familiarize yourself with all
operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Keyless chuck
2. Speed selector switch
3. Forward/reverse switch
4. Battery release buttons
5. Battery
6. ON/OFF trigger switch
7. LED light
8. Torque adjustment collar
9. Charger
10. LED charge state indicator
VIII - Operation
leD WORK AReA lIGHt
The machine is equipped with LED light (7) to illuminate
the work area and improve visibility when drilling in areas
with insufficient light. To turn the LED light on and off de-
press the LED light button (6).
ReveRsING
The extreme position of lever (3) to the right (viewed from
the rear) is equivalent to anti-clockwise rotation, the ex-
treme position to the left - to clockwise rotation. When
the ON/OFF switch (6) is depressed lever (3) can not be
actuated. (Fig. 2)
WARNING: Reversing can be performed only
when the spindle is not rotating!
Drilling and tightening screws are performed with lever
in extreme position to the left. Removal of screws is per-
formed with lever in extreme position to the right.
7
EN
8.6.2012 . 14:55:53 .