Tabla de contenido
Idiomas disponibles
Idiomas disponibles
• If excessive heat is produced, this indicates the device should not be used with this inverter.
• This problem does not occur with most of the battery-operated equipment. Most of these devices use a separate charger or
transformer that is plugged into an AC receptacle.
• The inverter is capable of running most chargers and transformers.
Power Inverter Output Waveform
The AC output waveform of this inverter is known as a modified sine wave. It is a stepped waveform that has characteristics
similar to the sine wave shape of utility power. This type of waveform is suitable for most AC loads, including linear and
switching power supplies used in electronic equipment, transformers, and small motors.
Using the Dual 120 Volt AC Outlets
The two 120 volt AC outlets each are located under a protective cover on the left hand side of the front panel (refer to the
Features section to locate). The two outlets support a combined maximum power draw of 500 watts.
1. Press the inverter power switch to turn the inverter on (I). The inverter power indicator will light red to indicate the two 120
volt AC outlets are ready to use.
2. Lift up the cover of the120 volt AC outlet.
3. Insert the 120 volt AC plug from the appliance into the 120 volt AC outlet.
4. Switch on the appliance and operate as usual.
5. Periodically check the unit's battery status by pressing the battery power level button. (Four solid bars in the battery icon
indicates a full battery. One bar indicates that the unit needs to be recharged.)
PROTECTIVE FEATURES
The inverter monitors the following conditions:
Low internal battery voltage: The inverter will automatically shut down when the battery voltage drops too low, as this can
harm the battery.
High internal battery voltage: The inverter will automatically shut down when the battery voltage is too high, as this can harm
the unit.
Thermal shutdown protection: The inverter will automatically shut down when the unit becomes overheated.
Overload/short circuit protection: The inverter will automatically shut down when an overload or short circuit occurs.
IMPORTANT NOTES: The inverter power/status indicator will flash red to indicate that one of the above fault conditions is
present before automatic shutdown occurs. Should this occur, take the following steps:
1. Disconnect all appliances from the unit.
2. Press the inverter power switch to turn the inverter off (O).
3. Allow the unit to cool down for several minutes.
4. Make sure the combined rating for all appliances plugged into the unit is 500 watts or lower and that appliance cord(s) and
plug(s) are not damaged.
5. Assure there is adequate ventilation around the unit before proceeding.
12 VOLT DC PORTABLE POWER SUPPLY
The 12 volt DC power supply is located under a protective cover on the front of the unit. Refer to the illustration of the
features on page 2 to locate. This portable power source is also for use with all 12 volt DC accessories equipped with a male
accessory outlet plug and are rated up to 5 amps.
1. Lift up the cover of the unit 's 12 volt DC outlet.
2. Insert the 12 volt DC plug from the appliance into the 12 volt accessory outlet on the unit. DO NOT EXCEED A 5 AMP LOAD.
3. Press the unit on/off button to turn the unit on.
4. Switch on the appliance and operate as usual.
5. Periodically check the unit's battery status on the LCD screen. (Four solid bars in the battery icon indicates a full battery. One
bar indicates that the unit needs to be recharged.)
USB CHARGING PORT
The USB charging port is under the same protective cover as the 12 volt DC outlet. Refer to the illustration of the features on
page 2 to locate.
1. Press the USB power on/off button to turn the USB port on. The backlit LCD screen will display the following:
+
Compressor
–
The "5V USB" icon indicates that the USB port is ready to use.
Area Light
5V
+
–
USB
Battery
Status
USB
10
2. Plug the USB-powered device into the USB power port and operate normally.
3. Periodically check the unit's battery status on the LCD screen. (Four solid bars in the battery icon indicates a full battery. One
bar indicates that the unit needs to be recharged.)
Notes:
This unit's USB power port does not support data communication. It only provides 5V DC/1000mA power to an external USB-powered device.
Some household USB-powered electronics will not operate with this unit.
PORTABLE COMPRESSOR
The built-in 12 volt DC compressor is the ultimate compressor for all vehicle tires, trailer tires and recreational inflatables. Three
different sized nozzle adapters are supplied. Each nozzle adaptor will screw onto the end of the SureFit™ nozzle located at
the free end of the compressor hose. The compressor hose with tire fitting is stored in a retaining channel between the jumper
cable channels on the rear of the unit. Refer to the "Features" illustration for locations of compressor hose. The compressor on/
off button and compressor pressure control buttons are located on the control panel on the front of the unit.
The compressor may be used by removing the air hose from the storage hatch and if required, fitting an appropriate nozzle
adapter to the air hose. The compressor is capable of inflating up to 120 pounds per square inch (psi) pressure. The compressor
can operate long enough to fill up to 3 average sized tires before the battery must be recharged. Return hose to the storage
compartment after use.
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN THE
"SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS" SECTION OF THIS INSTRUCTION MANUAL.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
Do not operate compressor continuously for extended periods of time (approximately 10 minutes, depending on ambient
temperatures), as it may overheat. In such event, compressor will automatically shut down. Immediately press the compressor
on/off button to turn the compressor off. Restart after a cooling down period of approximately 15 minutes.
Inflating Tires or Products With Valve Stems
1. Place connector (chuck) on valve stem.
2. Ensure connector is pushed on to valve stem as far as possible before closing thumb latch.
3. Make sure latch is secure.
4. Press the compressor on/off button. The backlit LCD screen will display the following:
+
Compressor
–
The number on the digital display will flash until a psi value is entered using the compressor pressure control buttons.
5. Press the "+" and "–" pressure control buttons to set the desired pressure. This must be a value between 1 and 100. Once
the pressure has been entered, the digital display will light solid. The backlit LCD screen will display the following:
+
Compressor
–
The digital display will show the psi value you have entered.
6. Press the compressor on/off button once more to begin inflating. Monitor the pressure on the LCD screen.
7. When desired pressure is reached, the compressor will automatically stop. Remove connector from valve stem.
8. Turn off the compressor by first pressing the compressor on/off button, then the unit on/off button.
9. Allow unit to cool, then recharge before storing away.
10. Store compressor hose and tire fitting in storage compartment.
Inflating Other Inflatables Without Valve Stems
Inflation of other items requires use of one of the adapters (nozzles).
1. Select the appropriate nozzle.
2. Screw the appropriate adapter (i.e. needle) into the SureFit™ nozzle.
3. Insert adapter (i.e., needle) into item to inflate to appropriate pressure.
4. Follow steps 4 through 10 of the "Inflating Tires or Products With Valve Stems" section.
Area Light
+
–
Battery
Psi
Status
USB
Area Light
–
+
Battery
Psi
Status
USB
11
Tabla de contenido
